Hard Disk Drive(s)

The Trinzic TE-1405, TE-1415, TE-1425 appliances, and Advanced Appliance PT-1405 each provide one (1) Infoblox hard disk storage device.
The Trinzic Reporting TR-1405 appliance, and Network Insight ND-1405 appliance provides two (2) hard disks in a RAID 1 array. Each disk drive has LEDs on the far left side of each drive carrier, that indicate the connection and activity status on the disk drive. The top LED flickers to blue when the disk drive is operational and performing read-write operations. The lower LED is dark (inactive) during all operations. Both drive LEDs are dark when the disk drive is not connected. You must use the Grid Manager UI or the NIOS CLI to verify disk operation. For more information, see Evaluating the Status of the Disk Subsystem.

On/Off Switch

A power switch to turn the power supply of the appliance on and off. The switch is hidden. Use a small blunt object, such as a paper clip, to gently push the switch.

Power LED

An LED that glows blue when there is power to the appliance. When it is dark, the appliance is not receiving power, even if the power cable is plugged in. When it glows red, there is an error. Ensure that you power on the appliance through the On/Off switch using a small blunt object, such as a paper clip.

IPMI Port

Dedicated Ethernet port used for LOM (Lights Out Management) with specific releases of NIOS. The IPMI/LOM Port supports 10/100/1000 Mbps operations. Ensure that the IPMI port is properly connected to the network before you configure LOM through the Grid Manager for remote management. The IPMI port auto-negotiates up to Fast Ethernet 1000BASE-TX speeds; ensure that the switch port to which the IPMI port connects will auto-negotiate to 1000 Mbps operation.

USB Port

Reserved for future use.

Console Port

A male DB-9 serial port for a console connection to change basic configuration settings and view basic system functions through the CLI (command line interface).
If your system lacks a DB-9 serial port, use a properly grounded USB-to-Serial dongle for connection to the serial console port. If the dongle is connected to a laptop, the laptop also must be properly grounded. Failure to do so may cause damage to the serial console port of the Infoblox appliance. Infoblox is not responsible for such damage. For DB-9 pin assignments, see Figure 4.

MGMT Port

A 10/100/1000-Mbps gigabit Ethernet port that you can use for appliance management or DNS service. You can enable the MGMT port and define its use through the Grid Manager after the initial setup.
The Advanced Appliance PT-1405 must be managed through its MGMT port.

HA Port (Active for high availability in the TE-1415 appliances and PT-1405)

A 10/100/1000-Mbps gigabit Ethernet port through which the active node in an HA (high availability) pair connects to the network using a VIP (virtual IP) address. HA pair nodes also use their HA ports for VRRP (Virtual Router Redundancy Protocol) advertisements.
ND-1405 and TR-1405 Reporting: The HA Port is inactive and reserved for future use.

LAN1 Port

A 10/100/1000-Mbps gigabit Ethernet port that connects the appliance to the network. You must use the LAN1 port to set up the appliance initially. It handles all traffic if you do not enable the MGMT and LAN2 ports. The passive node in an HA pair uses this port to synchronize the database with the active node.

LAN2 Port

A 10/100/1000-Mbps gigabit Ethernet port that connects the appliance to the network. The LAN2 port is disabled by default. You can enable the LAN2 port and define its use through the Grid Manager after the initial setup.

UID Button

The unit identification button. When you press the UID button, the UID LED on the front and rear panel glows blue. In a rack environment, the UID feature enables easier location of a server when moving between the front and rear of the rack. You can also identify the appliance through the Grid Manager and CLI commands.