You can configure the appliance to receive SNMP queries from specific management systems and send SNMP traps to specific trap receivers. SNMP operation supports both IPv4 and IPv6 networks. The appliance supports SNMPv1, SNMPv2, and SNMPv3. You can set up either SNMPv1/SNMPv2 or SNMPv3, or all of them for a Grid. You can also override the Grid settings at a member level.
To configure SNMPv1 and SNMPv2 on the appliance, do the following:
...
Grid: From the Grid tab, select the Grid Manager tab, and then select Grid Properties -> Edit from the Toolbar. Member: From the Grid tab, select the Grid Manager -> Members tab -> member, and then click the Edit icon.
In the Grid Properties or Grid Member Properties editor, click Toggle Advanced Mode, and then select the SNMP Threshold tab. To override Grid settings, click Override in the Grid Member Properties editor.
Complete the following in the SNMP Threshold tab. Each of the following event types have default Trigger and Reset values. You can change the values for any of them. You can set SNMP thresholds above or below which the appliance sends SNMP traps and email notifications, if configured to do so. When any allocated usage exceeds the Trigger value, the appliance sends an SNMP trap and email notification to the designated destination, and the status icon for that usage turns red. When usage drops to the Reset value, the status color goes back to normal and turns green.
CPU Usage: The percentage of the CPU that is currently in use. The default Trigger value is 81%, and the default Reset value is 70%. Note that these default values are set to disable the CPU usage trap. You can enable this trap and configure the trigger and reset values using the CLI command set thresholdtrap.
Sometimes you may see high CPU usage on Network Insight discovery members. In most cases, this high CPU usage is the result of CPU-intensive tasks run by the MySQL database during the consolidation of customer data. Network Insight is not a real-time system, so high CPU usage itself does not lead to loss of functionality. Therefore this alert should not be treated as critical if no other negative symptoms are observed on discovery members.Database Objects: The percentage of database capacity that is currently in use. The default Trigger value is 80%, and the default Reset value is 70%.
Disk: The percentage of the primary hard disk that is currently in use. The default Trigger value is 85%, and the default Reset value is 70%.
File Distribution Usage: The percentage of the file distribution storage capacity that is currently in use on the selected member. The default Trigger value is 90%, and the default Reset value is 70%.
IPAM Utilization: For a network, this is the percentage based on the IP addresses in use divided by the total addresses in the network and for a network container that contains subnets, this is the percentage of the total address space defined within the container regardless of whether any of the IP addresses in the subnets are in use. The default Trigger value is 95% and the default Reset value is 85%. The status icon turns red when utilization crosses the configured trigger value. When utilization is below the trigger value, the status color turns blue.
Memory: The percentage of the system memory that is currently in use. The default Trigger value is 90%, and the default Reset value is 80%.
Network Capacity: When the Grid is part of a Master Grid, this is the percentage of the Master Grid's network capacity that is used by the Grid's networks. The default Trigger value is 85% and default Reset value is 75%.
Recursive Clients: The percentage of the limit of concurrent recursive queries. The default Trigger value is 80%, and the default Reset value is 30%. You must also enable the recursive client limit in order for the appliance to send recursive client traps. For information about how to set this limit, see RestrictingRecursiveEnabling Recursive QueriesClientEnabling Recursive QueriesQueries. When you configure the Trigger and Reset values, ensure that you do not set them too low or too close together. If the Trigger and Reset values are too close together, the appliance may send excessive traps and email notifications because both trigger and reset traps are sent based on the calculated value of simultaneous recursive client queries. For example, when you set the recursive client limit at 50, Trigger value at 71%, and Reset value at 70%, the value for simultaneous recursive client queries is calculated at 50 x .71 = 35 (integer math truncation) and 50 x .70 = 35. This could result in the appliance sending trigger and reset traps for the same value of simultaneous recursive client queries.
Root File System: The percentage of the root file system ("/") that is currently in use. The default Trigger value is 85%, and the default Reset value is 70%.
Swap Usage: The percentage of the swap area that is currently in use. The factory default trigger value is 50% and the factory default reset value is 30%. Grid Manager displays zero for both the trigger and reset values indicating the optimized usage of platform specific default values. For information about available memory on each appliance model, see thetable below.
Reporting: The number of reports created on the system that can trigger an SNMP trap. The default Trigger value is 85, and the default Reset value is 70. Note that the maximum number of reports supported per Grid is 300. This field is displayed only when you have configured a reporting server.
Reporting Volume: The percentage of data transmissions to the reporting server. The default Trigger value is 80%, and the default Reset value is 71%. This field is displayed only when you have configured a reporting server.
Threat Protection Dropped Traffic: The percentage of packets dropped based on the threat protection rule configuration. The default Trigger value is 90%, and the default Reset value is 70%. This field is displayed only when Threat Protection licenses are installed on the appliance. When the percentage of Threat Protection dropped traffic exceeds the Trigger value or drops below the Reset value, the appliance sends an SNMP trap and an email notification — if configured to do so. For information about setting SNMP traps and email notifications, see Setting SNMP and Email Notifications in the following section.
Threat Protection Total Traffic: The percentage of total traffic received (dropped and passed packets) on the external interfaces. The default Trigger value is 90%, and the default Reset value is 70%. This field is displayed only when Threat Protection licenses are installed on the appliance. When the percentage of total Threat Protection traffic exceeds the Trigger value or drops below the Reset value, the appliance sends an SNMP trap and an email notification — if configured to do so.
If you have installed Threat Protection licenses on the appliance and are using the Infoblox feature, Grid Manager displays the following for Trigger events per second and Reset events per second:Alert Rate: The number of SNMP traps sent per second when the appliance sends alerts while passing packets based on threat protection rule configuration. The default trigger value is based on the events per second configured for the rule.
Drop Rate: The number of SNMP traps sent per second when the appliance drops packets based on the threat protection rule configuration. The default trigger value resets based on the number of events that are reset.
If you have installed an RPZ license on the NIOS appliance, you can configure the thresholds to monitor the RPZ hit rate in the Response Policy Zones Hit Rate Configuration section. For information, see Configuring Thresholds for RPZ Hit Rate.
Save the configuration and click Restart if it appears at the top of the screen.
...
Instead of enabling and receiving SNMP and email notifications for all hardware and software events, you can select specific alert types when a specific hardware or software encounters issues. To enable SNMP or email notifications for specific event types, select the corresponding checkboxes in the Notification tab of the Grid Properties or Member Properties editor. The following table lists the event types you can select:
Event Types
Event Type | Description | Sample SNMP Trap |
---|---|---|
Automated Traffic Capture | Sends notifications each time traffic capture is enabled or disabled or a support bundle is downloaded. For more information, see Enabling Automated Traffic Capture. | 01:09:57.938095 IP (tos 0x0, ttl 60, id 37373, offset 0, flags [DF], proto UDP (17), length 356) |
BGP | Sends notifications when the BGP software has failed. For more information about the table ibProbableCause Values (OID 3.1.1.1.2.4.0), see SNMP MIB Hierarchy. | 2012-11-22 04:49:06 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibRevokedLicense(53) |
Backup | Sends notifications about the status of backup operation. For more information about the Processing and Software Failure traps., see SNMP MIB Hierarchy. | 2011-09-22 09:14:17 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) |
BloxTools | Sends notifications about the status of bloxTools. For more information about the Object State Change traps, see SNMP MIB Hierarchy | 2011-09-13 20:38:46 10.34.42.4 [UDP: [10.34.42.4]:38187->[10.34.42.2]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (742156) 2:03:41.56 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.42.4" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: bloxTools IB-TRAP-MIB::ibPreviousState.0 = INTEGER: bloxtools-service-failed(41) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: bloxtools-service-working(39) IB-TRAP-MIB::ibTrapDesc.0 = STRING: BloxTools Service is working. |
CPU | Sends notifications about the status of CPU usage. For more information about the Threshold Crossing Event traps, see SNMP MIB Hierarchy. | 2012-04-12 01:54:59 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 5 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 3 IB-TRAP-MIB::ibTrapDesc.0 = STRING: CPU usage above threshold value. |
CaptivePortal | Sends notifications about the Captive Portal service. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2016-01-08 02:58:23 10.35.107.4 [UDP: [10.35.107.4]:45111->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (22280) 0:03:42.80 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.107.4" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: captive_portal IB-TRAP-MIB::ibPreviousState.0 = INTEGER: captive-portal-service-inactive(51) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: capative-portal-service-working(49) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Captive Portal Service is working. |
Cisco ISE | Sends notifications about the status of the Cisco ISE service. For more information about Object State Change Traps, see SNMP MIB Hierarchy. | 2016-01-07 22:26:19 10.40.240.111 [UDP: [10.40.240.111]:47355->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16384) 0:02:43.84 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.40.240.111" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: cisco_ise_server IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 124 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 123 IB-TRAP-MIB::ibTrapDesc.0 = STRING: CiscoISE server 10.36.141.15 is OK. |
Clear | Sends notifications when the SNMP trap is cleared. When you select the checkbox, the CLEAR trap is sent for the following software failures: LDAP servers, OCSP responders, LCD, Serial Console, OSPF, OSPF6, BGP, HSM, Controld, SSH, HTTP, Cluster, Login, and Duplicate IP. For file distribution, the trap is sent when the service is restored. If you deselect the checkbox, the CLEAR trap is not sent when any of the mentioned software fails. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2015-11-12 22:46:21 10.35.124.1 [UDP: [10.35.124.1]:48446->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (12793) 0:02:07.93 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.124.1" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Login IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibClear(0) IB-TRAP-MIB::ibTrapDesc.0 = STRING: SNMP Trap is cleared. GUI Login |
Cloud API | Sends notifications about whether the Cloud API service is functioning or not. for information about Cloud Network Automation, see Introduction to Cloud Network Automation. | 2014-11-13 00:52:37 10.35.114.10 [UDP: [10.35.114.10]:57772->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (480221) 1:20:02.21 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.114.10" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: cloud_api IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 105 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 103 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Cloud API service is working. |
Cloud |
Sync | Sends notification about the status of the Cloud |
Sync service. | DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (45114) 0:07:31.14 |
Sync Service is not running." DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (50781) 0:08:27.81 |
Sync Service is unhealthy." DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (52645) 0:08:46.45 |
Sync Service is initializing." DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (55591) 0:09:15.91 |
Sync Service is healthy." | ||
Cluster | Sends notifications about the status of NIOS clusterd process. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2011-12-10 09:43:23 infoblox.localdomain [UDP: [10.35.2.70]:44193->[10.35.2.70]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (47140) 0:07:51.40 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "0" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Clusterd_Monitor IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibFDSoftwareFailure(32) IB-TRAP-MIB::ibTrapDesc.0 = STRING: WATCHDOG: A grid daemon failure has occurred on 10.35.2.70 |
Controld | Sends notifications about the NIOS controld process. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2012-08-17 05:29:30 <UNKNOWN> [UDP: [10.32.2.80]:43475->[10.32.2.80]:162]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (24722) 0:04:07.22 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "192.168.1.2" IB-TRAP MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: controld IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibControldSoftwareFailure(11) IB-TRAP-MIB::ibTrapDesc.0 = STRING: A controld failure has occurred. |
DHCP | Sends notifications about the status of DHCP service. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2016-04-18 02:42:36 10.35.139.15 [UDP: [10.35.139.15]:35531->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (8809) 0:01:28.09 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.139.15" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: dhcpd IB-TRAP-MIB::ibPreviousState.0 = INTEGER: dhcp-service-inactive(48) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: dhcp-service-working(45) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DHCP Service is working. |
DNS | Sends notifications about the status of DNS service. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2016-01-08 01:10:53 10.35.3.154 [UDP: [10.35.3.154]:59876->[10.120.20.12]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (324160) 0:54:01.60 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.154" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING:DNS IB-TRAP-MIB::ibPreviousState.0 = INTEGER: dns-service-working(32) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: dns-service-inactive(34) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS Service is inactive. |
DNS Attack | Sends notifications about the status of the DNS attacks. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2016-01-07 23:55:56 10.35.3.201 [UDP: [10.35.3.201]:33199->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (25100) 0:04:11.00 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.201" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: DNSAttack IB-TRAP-MIB::ibPreviousState.0 = INTEGER: dns-attack-active(115) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: dns-attack-inactive(116) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS attack conditions have ended. |
DNS Forwarding | Sends notifications about whether DNS | 2017-11-03 14:06:19 192.168.1.3 [UDP: [192.168.1.3]:33577->[192.168.1.2]:162]: Trap, DISMAN-EVENT-MIB::sysUpTimeInstance = |
DNS Integrity Check | Sends notifications about whether DNS integrity check is functioning or not. For information about DNS integrity check, see Configuring DNS Integrity Check for Authoritative Zones. | 2014-06-03 05:35:45 10.34.82.121 [UDP: [10.34.82.121]:42577->[10.120.20.232]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (427200) 1:11:12.00 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.154.3" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibSubsystemName.0 = STRING: DNS Integrity Check IB-TRAP-MIB::ibProbableCause.0 =INTEGER: ibDNSIntegrityCheckNameserversFailed(102) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS Integrity Check is unable to connect to any name servers required to perform the check. There are list of nameservers failure: (['10.35.0.56']) |
DNS Integrity Check Connection | Sends notifications about whether DNS integrity check connection is functioning or not. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 016-01-12 05:10:27 10.35.129.15 [UDP: [10.35.129.15]:35201->[10.120.20.12]]: IB-TRAP-MIB::ibTrapSeverity.0= INTEGER: info(2) IB-TRAP-MIB: :ibPreviousState.0 = INTEGER: dns-integrity-check-severity-indetermined(97) |
Database | Sends notifications about the database status. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2013-04-05 02:27:01 10.35.116.2 [UDP: [10.35.116.2]:45332->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (120021) 0:20:00.21 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.116.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: db_usage IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 1 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 85 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 0 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Database capacity used is OK. |
Disconnected Grid | Sends notifications about whether a Grid has been disconnected from the Master Grid. For more information about object state change traps, see SNMP MIB Hierarchy. | 2011-12-27 23:38:44 IB-TRAP-MIB::ibObjectName.0 = STRING: ID_Grid IB-TRAP-MIB::ibTrapDesc.0 = STRING: The grid member is connected to the grid master. |
Discovery | Sends notifications about the discovery status. For information about the Discovery feature, see Infoblox Network Insight. | 2013-10-22 01:35:53 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: discovery_collector |
Discovery Conflict | Sends notifications about conflicts between the DHCP address and the existing IP address.For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2014-06-20 00:48:06 10.34.125.2 [UDP: [10.34.125.2]:36159->[10.120.20.232]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (2241) 0:00:22.41 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.125.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: DHCP IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibDHCPHostConflict(66) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DHCP address conflicts with an existing host address. [IP address] |
Discovery Unmanaged | Sends notifications related to the discovery of unmanaged devices and networks. You can configure the maximum number of unmanaged objects the appliance discovers and how often it notifies about these events. For more information about how to configure these parameters, see Defining Seed Routers for Probe Members. | 2015-02-09 22:53:57 10.35.103.18 [UDP: [10.35.103.18]:45156->[10.120.20.46]]: DISMAN-EVENT-MIB::sysUpTimeInstance =Timeticks: (46090) 0:07:40.90 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibOperationTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.103.18" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Discovery IB-TRAP-MIB::ibProbableCause.0 =INTEGER: 4012 IB-TRAP-MIB::ibTrapDesc.0 =STRING: New unmanaged devices/networks were found during network discovery process. New unmanaged devices in '10.40.16.0/20' network in 'default' network view. |
Disk | Sends notifications about the status of the primary disk. For more information about threshold crossing traps, see SNMP MIB Hierarchy. | 2012-11-22 03:34:32 IB-TRAP-MIB::ibObjectName.0 =STRING: disk_usage IB-TRAP-MIB::ibThresholdHigh.0 =INTEGER: 10 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 5 IB-TRAP-MIB::ibTrapDesc.0 = STRING: System primary hard disk usage is over |
DuplicateIP | Sends notifications when there are duplicate IP addresses. For more information about ibProbableCause Values, see SNMP MIB Hierarchy. | 2016-04-18 22:47:38 10.35.139.15 [UDP: [10.35.139.15]:35531->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (7239201) 20:06:32.01 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.139.15" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Equipment IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibDuplicateIPAddressFailure(52) IB-TRAP-MIB::ibTrapDesc.0 = STRING: A Duplicate IP Address has been detected. |
ENAT | Sends notifications about the Ethernet port status.For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2012-08-27 03:05:25 10.36.3.132 [UDP: [10.36.3.132]:47962->[10.120.20.232]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16624) 0:02:46.24 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.132" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibObjectName.0 = STRING: LAN IB-TRAP-MIB::ibPreviousState.0 = INTEGER: enet-link-up(6) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: enet-link-down(7) IB-TRAP-MIB::ibTrapDesc.0 = STRING: LAN1 port link is down. Please check the connection. |
File Distribution Usage | Sends notifications about the HTTP file distribution process. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2016-01-08 01:48:57 10.40.240.113 [UDP: [10.40.240.113]:41443->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (183757) 0:30:37.57 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.40.240.113" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: fd_usage IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibFDSoftwareFailure(42) IB-TRAP-MIB::ibTrapDesc.0 = STRING: File Distribution services storage usage is OK. |
FTP | Sends notifications about the status of FTP service. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2016-01-07 23:27:22 10.40.240.113 [UDP: [10.40.240.113]:36063->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (380473) 1:03:24.73 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.40.240.113" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: ftp IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibFTPDSoftwareFailure(44) IB-TRAP-MIB::ibTrapDesc.0 = STRING: An FTPD daemon failure has occurred. |
Fan | Sends notifications about the status of the system fan. For more information about lEquipment Failure Traps, see SNMP MIB Hierarchy. | 2012-02-23 23:34:50 10.32.1.222 [UDP: [10.32.1.222]:42742->[10.35.109.24]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (89508) 0:14:55.08 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibEquipmentFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.32.1.222" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: fan IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibFan1Failure(37) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Fan 1 failure has occurred. |
HA | Sends notifications about the status of the HA port link. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2014-05-23 00:49:32 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: HA_Replication |
HSM | Sends notifications about the status of the HSM operation. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2016-01-12 20:52:12 10.39.13.77 [UDP: [10.39.13.77]:44962->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (131909) 0:21:59.09 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.39.13.77" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: DNS IB-TRAP-MIB::ibPreviousState.0 = INTEGER: dns-service-working(32) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 55 IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS Service restarted not using HSM |
HTTP | Sends notifications about the status of the HTTP service. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2016-01-07 23:16:40 10.40.240.113 [UDP: [10.40.240.113]:36063->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (316247) 0:52:42.47 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.40.240.113" IB-TRAP-MIB::ibTrapSeverity.0= INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: http_file_dist IB-TRAP-MIB::ibPreviousState.0 = INTEGER: http-file-dist-service-inactive(40) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: http-file-dist-service-working(38) IB-TRAP-MIB::ibTrapDesc.0 = STRING: HTTP File Dist Service is working |
IFMAP | Sends notifications about the status of the IF-MAP service. For more information about ibProbableCause Values, see SNMP MIB Hierarchy. | 2016-04-20 23:40:00 10.34.41.60 [UDP: [10.34.41.60]:33231->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (45256) 0:07:32.56 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.41.60" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: ifmapd IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibIFMAPSoftwareFailure(50) IB-TRAP-MIB::ibTrapDesc.0 = STRING: An IF-MAP server failure has occurred. |
IPMI Device | Sends notifications about the status of the IPMI device. For more information about ibProbableCause Values, see SNMP MIB Hierarchy. | 2015-03-24 04:10:21 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibTrapDesc.0 = STRING: IPMI is used by some hardware monitors to test hardware health. The IPMI Device is now available; subsequent hardware monitor failures are likely to be genuine. |
IPAM Utilization | Sends notifications about the percentage of IPv4 addresses that are used in a network. For a network container that contains subnets, this indicates the percentage of the total address space defined within the container regardless of whether any of the IP addresses are used in the subnetwork. For more information about threshold crossing traps, see SNMP MIB Hierarchy. | 2014-07-06 19:33:01 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: Threshold IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 5 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 3 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Network IPAM Utilization capacity usage is OK. Network: 20.0.0.0/29/netview |
Load Balancer Device | Sends notifications about whether the LB device is in sync or not. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2013-07-08 02:36:39 10.35.113.2 [UDP: [10.35.113.2]:45568->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (996274) 2:46:02.74 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.113.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: device IB-TRAP-MIB::ibPreviousState.0 = INTEGER: lb-device-down(74) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: lb-device-up(73) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Load Balancer device 10.36.128.1 sync is OK. |
LCD | Sends notifications about the status of the LCD process. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2011-12-01 06:31:28 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibLCDSoftwareFailure(18) |
LDAP Servers | Sends notifications about whether LDAP servers are available or not. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2012-12-17 03:33:58 10.35.106.6 [UDP: [10.35.106.6]:35751->[10.120.20.249]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (4043) 0:00:40.43 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.106.6" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: ldap_servers IB-TRAP-MIB::ibPreviousState.0 = INTEGER: ldap-service-inactive(79) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: ldap-servers-ok(76) IB-TRAP-MIB::ibTrapDesc.0 = STRING: All LDAP servers are available. |
License | Sends notifications when the license has been revoked. For more information about Revoked License Trap, see SNMP MIB Hierarchy. | 2014-05-23 00:49:32 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Grid license of member IP 10.34.196.165 with hardware ID 564d5cf2115391ab3f6efee9a9d974aa is revoked. 0 Cold Start |
Login | Sends notifications when the login details are incorrect. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2013-04-30 02:56:49 10.34.132.2 [UDP: [10.34.132.2]:35453->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (27604) 0:04:36.04 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.152.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Login IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibGUILoginFailure(58) IB-TRAP-MIB::ibTrapDesc.0 = STRING: A GUI login failure has occurred. |
MGM | Sends notifications about the status of the multi-Grid configuration. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2013-04-03 23:48:34 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 23 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 24 IB-TRAP-MIB::ibTrapDesc.0 =STRING: Grid connection offline. |
MSServer | Sends notifications about the status of Microsoft Servers for Microsoft management. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2013-07-10 03:29:42 10.35.113.2 [UDP: [10.35.113.2]:51679->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (1066392) 2:57:43.92 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.113.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: ms_service IB-TRAP-MIB::ibPreviousState.0 = INTEGER: ms-service-down(20) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: ms-service-up(19) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Service connection to Microsoft DNS server 10.102.31.67 is OK. |
Memory | Sends notifications about the status of the system memory. For more information about threshold crossing traps, see SNMP MIB Hierarchy. | 2012-04-17 03:09:46 10.35.119.4 [UDP: [10.35.119.4]:37664->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (359835) 0:59:58.35 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.3 IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.119.4" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: memory IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 46 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 50 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 30 IB-TRAP-MIB::ibTrapDesc.0 = STRING: System memory usage is OK. |
NTP | Sends notifications about the status of the NTP service. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2013-04-02 23:58:19 10.35.116.6 [UDP: [10.35.116.6]:37505->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (17804) 0:02:58.04 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.1.187" IB-TRAP-MIB::ibObjectName.0 = STRING: ntp_sync IB-TRAP-MIB::ibPreviousState.0 = INTEGER: ntp-sync-down(16) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: ntp-sync-up(15) IB-TRAP-MIB::ibTrapDesc.0 = STRING: The NTP service resumed synchronization. |
Network | Sends notifications about the status of the LAN port. For more information about threshold crossing traps, see SNMP MIB Hierarchy. | 2013-01-06 23:52:01 10.35.3.62 [UDP: [10.35.3.62]:49255->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (80879) 0:13:28.79 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.3 IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.62" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: MGM IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 8 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 5 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 3 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Network capacity used is over the threshold value. |
OCSP Responders | Sends notifications about the status of OCSP responders. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2016-01-14 03:21:14 10.34.9.91 [UDP: [10.34.9.91]:34663->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (4599) 0:00:45.99 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.9.91" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: ocsp_responders IB-TRAP-MIB::ibPreviousState.0 = INTEGER: ocsp-responders-ok(65) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: ocsp-service-inactive(68) IB-TRAP-MIB::ibTrapDesc.0 = STRING: OCSP service inactive. |
OSPF | Sends notifications about the ospfd process. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2012-11-22 04:49:56 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibOSPFSoftwareFailure(35) |
OSPF6 | Sends notifications about the ospf process for IPv6. For more information about ibProbableCause Values (OID 3.1.1.1.2.4.0), see SNMP MIB Hierarchy. | 2016-01-13 02:03:07 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibClear(0) IB-TRAP-MIB::ibTrapDesc.0 = STRING: SNMP Trap is cleared. OSPF6 SW |
PowerSupply | Sends notifications about the status of the power supply. For more information about lEquipment Failure Traps, seeSNMP MIB Hierarchy. | 2012-01-20 22:45:01 nextgen.com [UDP: [10.32.111.110]:45323->[10.32.111.110]]: IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibSystemRestart(61) |
RAID | Sends notifications about the RAID array status. For more information about lEquipment Failure Traps, seeSNMP MIB Hierarchy. | 2016-01-15 14:30:20 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) |
Recursive Clients | Sends notifications about whether the DNS recursive server is under flood attacks. For more information about threshold crossing traps, see SNMP MIB Hierarchy. | 2015-01-13 02:05:55 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 800 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 300 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Number of simultaneous DNS recursive lookups is OK. |
RIR SWIP | Sends notifications about the status of the RIR SWIP registration. For more information about ibProbableCause Values (OID 3.1.1.1.2.4.0), see SNMP MIB Hierarchy. | 2016-01-11 02:05:17 10.34.11.100 [UDP: [10.34.11.100]:52957->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (43623) 0:07:16.23 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.11.100" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: RIR SWIP IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibRIRSWIPRegistrationFailure(89) IB-TRAP-MIB::ibTrapDesc.0 = STRING: An RIR SWIP registration failure has occurred.CREATE RIR registration request for network "187.0.0.0/24" failed. |
Reporting | Sends notifications about the status of the reporting database. For more information about threshold crossing traps, see SNMP MIB Hierarchy. | 2012-01-06 08:59:55 10.35.101.27 [UDP: [10.35.101.27]:59714->[10.35.117.24]]:DISMA N-EVENT-MIB::sysUpTimeInstance = Timeticks: (289200) 0:48:12.00 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.46.6" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: reporting_volume IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 85 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 80 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 71 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Reporting volume usage reached the threshold value. |
RPZ Hit Rate | Send Notifications about the percentage of RPZ Hit Rate.For more information about threshold crossing traps, see SNMP MIB Hierarchy. | 2016-04-18 02:52:29 10.35.139.15 [UDP: [10.35.139.15]:35531->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (68173) 0:11:21.73 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.139.15" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibObjectName.0 = STRING: RPZHitRate IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 100 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 1 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 0 IB-TRAP-MIB::ibTrapDesc.0 = STRING: RPZ hit rate is too high: 100%. |
RootFS | Sends notifications about the status of the root file system. For more information about threshold crossing traps, see SNMP MIB Hierarchy. | 2011-11-29 06:36:24 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 100 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 90 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Root filesystem disk usage is OK. |
SNMP | Sends notifications about the status of the SNMP server. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2012-02-17 06:24:11 |
SSH | Sends notifications about the status of the sshd process. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2011-09-21 21:33:17 10.34.42.6 [UDP: [10.34.42.6]:49776->[10.34.42.2]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (6508) 0:01:05.08 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.42.6" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: ssh IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibClear(0) IB-TRAP-MIB::ibTrapDesc.0 = STRING: SNMP Trap is cleared. SSHD SW |
SerialConsole | Sends notifications when the serial console login has failed or the admin failed to login to the serial console. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2014-12-15 02:47:59 UDP/IPv6: 2620:10a:6000:2400::8104]:55038 [UDP/IPv6: [2620:10a:6000:2400::8104]:55038]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (501585) 1:23:35.85 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "2620:10a:6000:2400::8104" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Login IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibSerialConsoleLoginFailure(59) IB-TRAP-MIB::ibTrapDesc.0 = STRING: A Serial Console login failure has occurred. |
Swap Usage | Sends notifications about whether the swap usage has exceeded the trigger or reset value. For more information about defining thresholds for traps, see above. | 2013-11-25 05:35:56 10.35.129.1 [UDP: [10.35.129.1]:49489->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (24009) 0:04:00.09 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.129.1" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibObjectName.0 = STRING: swap_usage IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 100 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 5 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 2 IB-TRAP-MIB::ibTrapDesc.0 = STRING: System swap space usage exceeds the critical threshold value. |
Syslog | Sends notifications when the syslog process stops. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2016-01-14 01:29:42 10.34.142.105 [UDP: [10.34.142.105]:37566->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (296285) 0:49:22.85 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.142.105" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: check_syslog_conf IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibSyslogFailure(67) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Syslog daemon is not running. |
System | Sends notifications about the status of the NIOS system. For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2014-03-14 05:54:42 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibSystemRestart(61) |
TAXII | Sends notifications when you start and stop the TAXII service. For more information about object state change traps, see SNMP MIB Hierarchy. | 2016-01-06 20:16:13 |
TFTP | Sends notifications about the status of the TFTP service.For more information about processing and software failure traps, see SNMP MIB Hierarchy. | 2011-09-16 06:54:08 IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibTFTPDSoftwareFailure(27) |
Threat Analytics | Sends notifications about the status of the Threat Analytics service. For more information about ibProbableCause Values (OID 3.1.1.1.2.4.0), see SNMP MIB Hierarchy. | 2016-01-08 00:19:34 10.35.3.154 [UDP: [10.35.3.154]:59876->[10.120.20.12]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16184) 0:02:41.84 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.154" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: Threat Analytics IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 127 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 126 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Threat Analytics Service is working. |
Threat Analytics DNS Tunneling | Sends notifications about the DNS tunneling detection. For more information about ibProbableCause Values (OID 3.1.1.1.2.4.0), see SNMP MIB Hierarchy. | 2016-01-08 00:22:07 10.35.3.154 [UDP: [10.35.3.154]:59876->[10.120.20.12]]: IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibProbableCause.0 = INTEGER: 4013 IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS Tunneling detected: The record '*.any.knjuqljsfyyc2t.com' is successfully added into BlackList RPZ zone with comment '[2016-08-01 08:22:06 UTC] [member: infoblox.localdomain] DNS Tunneling' and policy 'No Data'. |
Threat Protection | Sends notifications about whether the threat protection service for Infoblox DNS Protection is functioning properly. For more information about the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) tables, see SNMP MIB Hierarchy. | 2016-04-18 22:48:08 10.35.139.15 [UDP: [10.35.139.15]:54407->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (3926) 0:00:39.26 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.139.15" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: threat_protection IB-TRAP-MIB::ibPreviousState.0 = INTEGER: threat-protection-service-inactive(93) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: threat-protection-service-inactive(93) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Threat Protection Service is inactive. |
TmpFS | Sends notifications about the status of the Temporary file system. | 2024-04-11 11:24:34 <UNKNOWN> [UDP: [10.35.203.18]:58738->[10.120.23.198]:162]: |
Testing the SNMP Configuration
...