...

To enable the cloud platform feature on a Trinzic X6 series appliance member, you must install the Cloud Platform feature license. All of the X6 series appliances support the Cloud Platform license. Unlike Trinzic X5 series, there are no dedicated CP appliances in the X6 series appliances.

The impact of NIOS 9.0.1 and later versions on licensing is as follows:

• If you install new feature licenses in NIOS 9.0.1, NIOS verifies the new licenses by comparing it with the existing ones, validates them, and reports whether the new licenses are valid or invalid. When you save the result, all valid licenses are installed.

• If you replace a Trinzic X5 series appliance with a Trinzic X6 series appliance, the existing licenses that are still active can be transferred over to the newer appliance after getting new license-keys based on the replaced X6 series appliance. Active perpetual licenses are applied as subscription licenses as perpetual licenses are not offered from NIOS 9.0.1 onwards.

• In case of VMs, you must reprovision the VM resources based on the X6 series hardware model that you chose for the deployment.

This topic includes the following sections:

License Types

Infoblox licenses are divided into the following classes:

...

Adding Licenses

For a physical appliance of Trinzic X6 series, you must install licenses for the supported NIOS software models using the CLI only. Installing the NIOS software model licenses from Grid Manager (by uploading the license file or pasting the license information) is not supported.

...

• set license: Contact the Infoblox Support to obtain the license string and then use this command to add the license.

• set temp_license: Use this command to generate and install temporary licenses. For more information, see the Adding Temporary License section.

Verifying Licenses

When you install new feature licenses in NIOS 9.0.1, you can check whether the licenses being installed are valid, view the comparison between the existing and newly added licenses, and verify for any license conflicts by clicking Verify License(s). If the licenses pass validation, you can see the licenses that will be applied and those that will be discarded or overwritten, and you can either confirm or cancel applying new licenses.

...

Reshaping of NIOS Licenses

A Trinzic X6 series hardware appliance model supports software models of the X6 series and some models of the X5 series. The naming convention used for the software appliance models is as follows:

...

For any Trinzic X6 series hardware appliance, you may reshape NIOS by switching one supported software appliance model to another based on your requirement. Depending on the models switched, the change automatically triggers either a product restart or a repartitioning of the storage disk.

To switch to another supported model:

1. Back up the data on the NIOS appliance.

2. Run the reset all licenses command.
   The command clears all data on the appliance.

3. Install the license to switch to the required software model.
   For the software models supported by a hardware appliance, refer to the specific hardware installation guide available in the Infoblox Documentation Portal.
   Depending on the models switched, the change automatically triggers either a product restart or a repartitioning of the storage disk as listed in the below table.

The following table lists the impact of NIOS reshape activity:

Licensing Limitations in NIOS 9.0.1 and Later

From Trinizic X6 series appliances, Cloud Platform feature is offered through a license rather than a CP-xxxx virtual appliance. The limitations of the Cloud Platform license has been called out in this section along with other limitations of NIOS 9.0.1.

Cloud Platform License Limitations

• The license can be applied only on a Grid member but not on a Grid Master, a Grid Master Candidate, or a standalone appliance.

• The license cannot be applied on a member that has Network Insight or Reporting license installed.

• The license is independent of Cloud Network Automation license.

• The license is supported on a Trinzic X6 series hardware and software models (VM) but not on X5 series hardware and VM.

• If you need to delete a Grid member that has a Cloud Platform license installed, you must first delete the Cloud Platform license and then delete the member.

• The license can be installed on a Grid Master through cloud-init, However, Infoblox recommends that you set it as a Grid member before joining it to the Grid.

• A vNIOS member that has a Cloud Platform license installed, is not allowed to join a Grid if it is being configured as a Grid Master or a Grid Master Candidate.

• If a Grid member that has the Cloud Platform license installed is disassociated from its Grid Master by running the set nogrid command, you must retain it as a Grid member because the Cloud Platform license is not supported on a Grid Master or a standalone appliance.

Other Limitations

• Perpetual/permanent licenses are not supported on Trinzic X6 series appliances.

• Installing NIOS software model licenses for X6 series physical appliance from Grid Manager is not supported. You must install them from the CLI.

• When installing multiple licenses, ensure to sequence the order of installation in such a way that the dependency conflict does not occur.

• If you install a Multi-Grid Management license, you must manually perform a product restart using either the CLI or Grid Manager to set up Multi-Grid management.

• TR (reporting) and ND (Discovery) appliances will not run DDI.

• Revoking or disassociating a pool license from a member is not supported. If you replace an expired pool license with an active license, the license is installed as a new license leaving the expired license as is. If a valid static license is installed for the same feature, then the dynamic license is deleted and returned to the pool it belongs.

• Downgrading NIOS on a Trinzic X6 series appliance to a version prior to 9.0.1 is not supported. Trinzic X6 series appliances are supported only from NIOS 9.0.1 onwards.

• Installing NIOS software model licenses that are not compatible with a Trinzic X6 series physical appliance may show a successful message when installed using the CLI. Such licenses are not installed in the backend.
  For example: If you install an TE-2326 license over an TE-4126 appliance using the CLI, the installation shows a successful message but the license is not installed.
  For the list of supported appliances, see the hardware installation guide available of the specific X6 appliance or the Infoblox NIOS Release Notes that is available in the Infoblox Support portal.

...