| Note | ||
|---|---|---|
| ||
From NIOS-9.x release, IB-4030 and IB-4030-10GE appliances are not supported. |
The NIOS-based IB-4030 or IB-4030-10GE appliance provides several commands to change settings in the system. To use these commands, you must connect through SSH or connect through the serial console port to the IB-4030 or IB-4030-10GE and login with the appropriate admin account.
The IB-4030 or IB-4030-10GE appliance supports the standard NIOS command-line interface for communicating with the device. For more information, refer to the Infoblox CLI Guide.
...
- set dns transfer–Schedules zone transfers. Note that set dns transfer is not used by IB-4030 or IB-4030-10GE with an active DNS Cache Acceleration license.
- set monitor dns –Activates DNS monitoring in NIOS. This command is disabled on IB-4030 or IB-4030-10GE with an active DNS Cache Acceleration license.
- show monitor dns –Displays DNS network monitoring data. This command is disabled on IB-4030 or IB-4030-10GE with an active DNS Cache Acceleration license.
- set interface–Defines port speed and duplex settings for all supported interfaces.
- show interface–Shows the status and configuration of a chosen port.
- show smartnic–Shows the cusrrent status of the appliance. This command applies only to IB-4030 or IB-4030-10GE appliances.
- show smartnic-cache–You can view the current accelerator cache contents or view the prior cache dump file. This command may affect DNS query response performance for around 15 seconds during execution. This command applies only to IB-4030 and IB-4030-10GE appliances with DNS cache acceleration license enabled.
- set smartnic log–Specify the log level for the DNS Cache Acceleration service on the appliance.
- set temp_license–Generates and installs a temporary DNS cache acceleration license. You can add a temporary DNS cache acceleration license for up to one million qps. Note that you cannot add a temporary license if a permanent license already exists.
- show license–Displays the capacity of the applicable DNS cache acceleration license type.
- show smartnic-cache existing-file–Displays the existing cache data file of IB-4030 and IB-4030-10GE.
The CLI commands listed below are frequently used on the appliance. For detailed information about the supported CLI commands, refer to the Infoblox CLI Guide.
...
set dns
...
The set dns command enables you to control the DNS cache. You can flush the cache of a DNS view or flush a particular entry from the cache.
...
Infoblox > set dns flush name accounting.corp100.com Infoblox > set dns flush all
...
show dns
...
The show dns command displays DNS query statistics for all DNS views in the IB-4030 or IB-4030-10GE appliance. It also displays the recursive cache for the specified DNS views.
...
Infoblox > show dns stats success 6718810 referral 0 nxrrset 0 nxdomain 0 recursion 257 failure 0
...
set smartnic log
...
...
Sets the logging level for the DNS Cache Acceleration service on the IB-4030 or IB-4030-10GE appliance, where the level is between 0 being the least verbose and 7 being the most verbose.
...
Infoblox > set smartnic log 7
...
show smartnic
...
...
Checks the status and settings of the DNS Cache Acceleration service.
| Note | ||
|---|---|---|
|
...
When you use this command on a specific appliance, the configuration applies only to that appliance. When using this command for an HA pair, you must run the command separately on both the active and passive nodes to ensure consistent behavior. |
Show smartnic displays the following operating characteristics of the IB-4030 or IB-4030-10GE:
...
Infoblox > show smartnic Firmware version: 1.3.19, Nov 08, 2011
Cache: Enabled Cache hit count: 109397 Cache miss count: 3008
Minimum cached TTL: 10 DNS query stats: SUCCESS=109380 NXDOMAIN=0 NXRRSET=0 FAILURE=0 REFERRAL=0 DNS UDP packet count: port0=299339 port1=93408 port2=0 port3=0
Log level: 6 Failed cores: None
...
...
This command displays details about interfaces and SFPs that are connected to the IB-4030 or IB-4030-10GE platform.
Syntax
show interface
Example
Infoblox > show interface
LAN:
IP Address: 10.35.2.40 MAC Address: 00:0F:B7:24:10:15
Mask: 255.255.0.0 Broadcast: 10.35.255.255
MTU: 1500 Metric: 1
IPv6 Address: 2001:db8:a23::228/64
IPv6 Link: fe80::20f:b7ff:fe24:1015/64
Status: UP BROADCAST RUNNING MULTICAST
SFP Type: Fiber SX
SFP Model: Finisar(FTLF8519P2BCL)
Statistics Information
Received
packets: 6895339 bytes: 444006210 (423.4 MiB)
errors: 0 dropped: 14
overruns: 0 frame: 0
Transmitted
packets: 14832 bytes: 14599721 (13.9 MiB)
errors: 0 dropped: 0
overruns: 0 carrier: 0
Collisions: 0 Txqueuelen: 1000
You can view information about the SFPs on the IB-4030 or IB-4030-10GE application. To view the details:
From the Grid tab, select the Grid Manager tab and click the Members tab -> member check box -> Detailed Status icon.
You can also use this command to view the VLAN ID, tagged networks, and additional IP addresses that are configured for the network when you enable VLAN on an IB-4030 or IB-4030-10GE appliance. For more information , see Enabling VLAN Support Using CLI Commandsabout enabling VLAN support using CLI commands, see Infoblox DNS Firewall.