To deploy a single independent NIOS appliance, you cable its LAN1 port to the network and change its default IP settings so that it can connect to its surrounding IP address space. The default LAN settings are as follows:

...

When deploying a single independent appliance, you can use one of the following methods to set up the initial configuration:

• Method 1 – - Using the LCD
  • Requirements: Physical access to a powered up NIOS appliance.
  • Advantage: You do not need any other equipment.
• Method 2 – - Using the CLI
  • Requirements: A serial connection from your management system to the console port on the NIOS appliance. You can also enable remote console access so that you can use the CLI over a network connection. For information, see Restricting GUI/API Access.
  • Advantage: You do not need to change the IP address of the management system to connect to the NIOS appliance.
• Method 3 – - Using the Infoblox NIOS Startup Wizard
  • Requirements: An HTTPS connection from your management system to the LAN1 port on the NIOS appliance.
  • Advantage: The wizard provides step-by-step guidance for changing not only the IP settings for the LAN1 port, but also changing the appliance host name and admin password, setting the system clock, and—if using NTP (Network Time Protocol)—enabling the NIOS appliance to be an NTP client.

...

Figure 6.3 Infoblox LCD and Navigation Buttons Image Removed
InfobloxThe LCD panel is on the front of some of the NIOS appliances.
LCDNavigation Buttons

You can deploy a single independent NIOS appliance by Image Added

You can deploy a single independent NIOS appliance by setting its LAN1 port IP address, netmask, and gateway through the LCD. This is the simplest method because you do not need anything other than a physical access to the appliance to complete the initial configuration.

...

Figure 6.4 Console Connection

...

...

To Power Source

...

...

    2. Use a serial terminal emulation program, such as Hilgraeve Hyperterminal® (provided with Windows® operating systems), to launch a session. The connection settings are:

...

1. If you have not changed the default IP address (192.168.1.2/24) of the LAN1 port through the LCD or CLI—and the subnet to which you connect the appliance is not 192.168.1.0/24—put your management system in the 192.168.1.0/24 subnet and connect an Ethernet cable between the management system and the appliance.
2. Open an Internet browser window and enter https:// <IP address of the appliance> to make an HTTPS connection. For information about supported browsers, see Supported Browsers.
   Several certificate warnings may appear during the login process because the preloaded certificate is self-signed and has the hostname www.infoblox.com, which may not match the destination IP address you entered in step 1. To stop the warning messages from occurring each time you log in to Grid Manager, you can generate a new self-signed certificate or import a third-party certificate with a common name that matches the FQDN (fully qualified domain name) of the appliance. For information, see Managing Certificates.
3. Enter the default username and password (admin and infoblox) on the Grid Manager login page, and then click Login or press Enter. For information, see Logging in to the GUI.
4. Read the Infoblox End-User License Agreement. If you want to participate in the Infoblox Customer Experience Improvement Program, complete the following:
   • Participate in the Infoblox Customer Experience Improvement Program: Select the check box to send product usage data to Infoblox on a periodic basis. Infoblox uses this data to improve product functionality. For more information about the program, see Participating in the Customer Experience Improvement Program.
   • Support ID (optional): Enter the Infoblox Support ID that was assigned to your account. It must be a number with four to six digits. The value you enter here is also displayed in the Customer Improvement tab in the Grid Properties editor. Infoblox includes this ID in the data report.
   • Infoblox Privacy Policy: Click here to view the Infoblox privacy policy. The appliance displays the policy in a new browser tab.
     Click I Accept. The NIOS Setup wizard appears.
5. In the first screen of the NIOS Setup wizard, complete the following:
   • Type of Network Connectivity: Select the type of network connectivity for the appliance from the drop-down list:
     • IPv4 and IPv6: Select this to configure a dual mode appliance.
     • IPv4: Select this to configure an IPv4 appliance.
     • IPv6: Select this to configure an IPv6 appliance.
   • Are you configuring an HA pair or a standalone appliance?: Select Configuring a standalone appliance. To configure an independent HA pair, see Deploying an Independent HA Pair.
6. Click Next and complete the following to configure network settings:
   • Host Name: Enter a valid domain name for the appliance.
   • Ports and Addresses: This table lists the network interfaces based on the type of network connectivity of the appliance. For an IPv4 appliance, specify the network information for LAN1 (IPv4) interface and for an IPv6 appliance, specify the network information for LAN1 (IPv6) interface. For a dual mode appliance, specify the network information for both LAN1 (IPv4) and LAN1 (IPv6) interfaces.
     Enter correct information for the following by clicking the field:
     • Interface: Displays the name of the interface. You cannot modify this.
     • IP Address: Type the IPv4 or IPv6 address depending on the type of interface. An IPv6 address is a 128-bit number in colon hexadecimal notation. It consists of eight 16-bit groups of hexadecimal digits separated by colons (example: 2001:db8:0000:0123:4567:89ab:0000:cdef or 2001:db8::123:4567:89ab:0:cdef).
     • Subnet Mask (IPv4) or Prefix Length (IPv6): Specify an appropriate subnet mask for IPv4 address or prefix length for IPv6 address. The prefix length ranges from 2 to 127.
     • Gateway: Type the IPv4 or IPv6 address of the default gateway depending on the type of interface. For IPv6 interface, you can also type Automatic to enable the appliance to acquire the IPv6 address of the default gateway and the link MTU from router advertisements.
     • Port Settings: Select the port settings from the drop-down list. The list contains all the settings supported by the hardware model. The default is Automatic. The appliance automatically detects the port settings.
7. Click Next and complete the following to set admin password:
   • Yes: To change the default password.
   • No: To keep the default password. Infoblox recommends that you change the default password.
     When you select Yes, complete the following:
   • Password: Enter a password for the superuser admin account. The password must be a single alphanumeric string without spaces and at least four characters long. The password is case-sensitive.
   • Retype Password: Enter the same password.
8. Click Next and complete the following to configure time settings:
   • Time Zone: Select the applicable time zone from the drop-down list. The default is (UTC) Coordinated Universal Time.
   • Would you like to enable NTP?:
   • Select Yes to synchronize the time with external NTP servers, and then click the Add icon. Grid Manager adds a row to the NTP Server table. Click the row and enter either the IP address (IPv4 or IPv6) or the resolvable host name of an NTP server. You can view a list of public NTP servers at ntp.isc.org.
   • Select No to specify the time settings for the appliance.
   • Date: Enter the date in YYYY-MM-DD format. You can also click the calendar icon to select a date from the calendar widget.
   • Time: Enter the time in HH:MM:SS AM/PM format. You can also click the clock icon to select a time from the drop-down list.
9. If you want to participate in the Infoblox Customer Experience Improvement Program, complete the following and then click Next:
   • Participate in the Infoblox Customer Experience Improvement Program: Select the check box to send product usage data to Infoblox on a periodic basis. Infoblox uses this data to improve product functionality. For more information about the program, see Participating in the Customer Experience Improvement Program.
   • Support ID (optional): Enter the Infoblox Support ID that was assigned to your account. It must be a number with four to six digits. The value you enter here is also displayed in the Customer Improvement tab in the Grid Properties editor. Infoblox includes this ID in the data report.
   • Email: Enter an email address to which Infoblox sends a copy of the usage report. The email address you enter here is also displayed in the Customer Improvement tab in the Grid Properties editor. This is optional.
   • Infoblox Privacy Policy: Click here to view the Infoblox privacy policy. The appliance displays the policy in a new browser tab.
10. Click Next to view the summary of the configuration. Review the information and verify that it is correct. You can change the information you entered by clicking Previous to go back to a previous step.
11. Click Finish.
    The appliance restarts and disconnects Grid Manager.

In a dual mode independent appliance, the communication protocol for all the services is set to IPv4, by default. You can change the default communication protocol for the services. For information, see Changing the Communication Protocol for a Dual Mode Independent Appliance.

Anchor
Changing the Communication Protocol for Changing the Communication Protocol for

Anchor
bookmark711 bookmark711

Changing the Communication Protocol for a Dual Mode Independent Appliance

...