Note: SNMP operation is not supported across the NIOS appliance's LAN2 interface.

You can configure the appliance to receive SNMP queries from specific management systems and send SNMP traps to specific trap receivers. SNMP operation supports both IPv4 and IPv6 networks. The appliance supports SNMPv1, SNMPv2, and SNMPv3. You can set up either SNMPv1/SNMPv2 or SNMPv3, or all of them for the Grid. You can also override the Grid settings at a member level.
To configure SNMPv1 and SNMPv2 on the appliance, do the following:

Enable the NIOS appliance to accept queries, as described in Accepting Queries .
Specify the management systems to which the appliance sends traps, as described in Adding Trap Receivers .
Specify system information using managed objects in MIB-II, the standard MIB defined in RFC 1213. For information, see Setting SNMP System Information .

To configure SNMPv3 on the appliance, do the following:

Add an SNMPv3 user and set up authentication and privacy protocols. For information, see Configuring SNMPv3 Users . After you set up an SNMPv3 user, you can modify and delete it. For information, see Modifying SNMPv3 Users and Deleting SNMPv3 Users .
Enable the NIOS appliance to accept queries, as described in Accepting Queries .
Specify the management systems to which the appliance sends traps, as described in see Adding Trap Receivers .
Specify system information using managed objects in MIB-II, the standard MIB defined in RFC 1213. For information, see Setting SNMP System Information .

Configuring SNMPv3 Users

To enable SNMPv3, you must first configure SNMPv3 users on the appliance. For information about SNMPv3, see
About User-Based Security Model in SNMPv3 . To configure an SNMPv3 user:

From the Administration tab, select the SNMPv3 Users tab, and then click the Add icon.
In the Add SNMPv3 User wizard, complete the following:
- Name: Enter a user name for the SNMPv3 management system.
- Authentication Protocol: Select one of the following:
  - MD5: Select this to use the HMAC-MD5-96 authentication protocol to authenticate the SNMPv3 user.
    This protocol uses the MD5 (Message-Digest algorithm 5) hash function in HMAC (Hash-based Message Authentication Code) and truncates the output to 96 bits. The output is included as part of the SNMP message sent to the receiver. For detailed information about the protocol, refer to RFC1321, The MD5 Message-Digest Algorithm.
  - SHA: Select this to use the HMAC-SHA-96 authentication protocol to authenticate the SNMPv3 user.
    This protocol uses the SHA (Secure Hash Algorithm) hash function and truncates the output to 96 bits. The output is included as part of the SNMP message sent to the receiver.
  - None: Select this to decline using any authentication protocol for this SNMPv3 user. When you select this option, you are not required to enter a password.
    - Password: Enter a password for the selected authentication protocol.
    - Confirm Password: Enter the same password.
- Privacy Protocol: Select one of the following:
  - DES: Select this to use DES for data encryption. DES is a block cipher that employs a 56-bit key size and 64-bit block size in the encryption.
  - AES: Select this to use AES for data encryption. AES is a symmetric-key encryption standard that comprises three block ciphers, AES-128, AES-192, and AES-256. Each of these ciphers has a 128-bit block size and a key size of 128, 192, and 256 bits, respectively.
  - None: Select this to decline using any privacy protocol for this SNMPv3 user. When you select this option, you are not required to enter a password.
  - - Password: Enter a password for the privacy protocol.
    - Confirm Password: Enter the same password.
- Comment: Enter useful information about the SNMP user, such as location or department.
- Disable: Select this check box to retain an inactive profile for this SNMP user in the configuration. You can clear this check box to activate the profile.

Note: If an SNMPv3 user is configured to send SNMP queries, you cannot delete the user.

3. Click Next to define extensible attributes. For information, see Using Extensible Attributes .

4. Save the configuration.

Modifying SNMPv3 Users

From the Administration tab, select the SNMPv3 Users tab -> snmpv3user, and then click the Edit icon.
The SNMPv3 User editor provides the following tabs from which you can edit data:
- General: Modify the data as described in Configuring SNMPv3 Users .
- Extensible Attributes: Add and delete extensible attributes that are associated with the SNMPv3 user account. You can also modify the values of extensible attributes. For information, see Using Extensible Attributes .
Save the configuration.

Deleting SNMPv3 Users

When you delete an SNMPv3 user that is configured to send queries or receive traps, a warning message states that the SNMPv3 is associated with the corresponding function. You can then decide whether you want to delete the user or not.
To delete an SNMPv3 user:

From the Administration tab, select the SNMPv3 Users tab -> snmpv3user, and then click the Delete icon.
In the Delete confirmation dialog box, click Yes.

Note: You cannot schedule the deletion of an SNMPv3 user.

Accepting Queries

You can allow specific management systems to send SNMP queries to a NIOS appliance. For SNMPv1 and SNMPv2, you must specify a community string. The appliance accepts queries only from management systems that provide the correct community string. You can also specify SNMPv3 users to send queries. For information about configuring SNMPv3 users, see Configuring SNMPv3 Users .
To configure an appliance to accept SNMP queries:

Grid: From the Grid tab, select the Grid Manager tab, and then select Grid Properties -> Edit from the Toolbar. Member: From the Grid tab, select the Grid Manager -> Members tab -> member, and then click the Edit icon.
In the Grid Properties or Grid Member Properties editor, select the SNMP tab. To override Grid settings, click Override in the Grid Member Properties editor.
Complete the following in the SNMP section.
- Enable SNMPv1/SNMPv2 Queries: Select this to accept SNMPv1 and SNMPv2 queries from management systems.
  - Community String: Enter a text string that the management system must send together with its queries to the appliance. A community string is similar to a password in that the appliance accepts queries only from management systems that send the correct community string. Note that this community string must match exactly what you enter in the management system.
- Engine ID: Displays the engine ID of the appliance that manages the SNMP agent. The management system needs this ID to send traps to the appliance. If the appliance is an HA pair, this field displays the engine IDs for both the active and passive nodes.
- Enable SNMPv3 Queries: Select this to enable queries from SNMPv3 management systems. Click the Add icon to add SNMPv3 users that you have configured on the appliance. In the SNMPv3 User Selector dialog box, click the SNMPv3 user you want to add. The appliance displays the selected SNMPv3 users in the table. You can add comments in the table. You can also select an SNMPv3 user and click the Delete icon to remove it from the table. Note that a disabled SNMPv3 user cannot send queries to the appliance.

4. Save the configuration.

Adding Trap Receivers

You can enable the NIOS appliance to send traps to specific management systems using either SNMPv1/SNMPv2 or SNMPv3, or all versions of SNMP. You can then add management systems that are allowed to receive traps from the appliance. Note that you cannot enable both SNMPv1/SNMPv2 and SNMPv3 on the same trap receiver. The appliance sends traps when certain events occur. You can enable SNMP traps and add trap receivers to the Grid. You can also override the Grid settings at the member level.
To enable the appliance to send traps and to add trap receivers, do the following:

Grid: From the Grid tab, select the Grid Manager tab, and then select Grid Properties -> Edit from the Toolbar. Member: From the Grid tab, select the Grid Manager -> Members tab -> member, and then click the Edit icon.
In the Grid Properties or Grid Member Properties editor, select the SNMP tab. To override Grid settings, click Override in the Grid Member Properties editor.
Complete the following in the SNMP tab:
- Enable SNMPv1/SNMPv2 Traps: Select this to enable the appliance to send traps to specified management systems.

- - Community String: Enter a text string that the NIOS appliance sends to the management system together with its traps. Note that this community string must match exactly what you enter in the management system.
- Enable SNMPv3 Traps: Select this to enable the appliance to send traps to specified SNMPv3 users.

4. Click the Add icon and select one of the following from the drop-down menu to add an SNMP trap receiver:

- SNMPv1/SNMPv2: Select this to add an SNMPv1 or SNMPv2 management system as a trap receiver. Grid Manager adds a row to the table. In the Address field, enter the IP address of the SNMP management system to which you want the SNMP agent on the appliance to send traps. You can enter more than one trap receiver. To remove a trap receiver from the list, select the address, and then click the Delete icon.
- SNMPv3: Select this to add an SNMPv3 management system as a trap receiver. Grid Manager displays the SNMPv3 User Selector dialog box. Click the name of the SNMPv3 user in the dialog box. Grid Manager adds the user to the table. In the Address field, enter the IP address of the SNMP management system to which you want the SNMP agent on the appliance to send traps. You can add more than one trap receiver. To remove a trap receiver from the list, select the address, and then click the Delete icon.
  Trap receiver IP addresses may be in IPv4 or IPv6 format.

In the Trap Receiver table, Grid Manager displays the following information about the trap receivers:

- Address: The IPv4 or IPv6 address of the trap receiver. Note that when an SNMPv3 user is disabled, SNMPv1/SNMPv2 traps are disabled. You can modify the IP address of the trap receiver even when the following are disabled: SNMPv3 users, SNMPv1/SNMPv2 traps, and SNMPv3 traps.
- SNMPv3 User: The user name of the SNMPv3 trap receiver. This is for SNMPv3 only.
- Comment: Information you entered about the management system.

5. Save the configuration.

Setting SNMP System Information

You can enter values for certain managed objects in MIB-II, the standard MIB defined in RFC 1213. Management systems that are allowed to send queries to the appliance can query these values. You can enter these values for the Grid and specific members. You can also override the Grid values at a member level.
To enter system information:

Grid: From the Grid tab, select the Grid Manager tab, and then select Grid Properties -> Edit from the Toolbar. Member: From the Grid tab, select the Grid Manager -> Members tab -> member, and then click the Edit icon.
In the Grid Properties or Grid Member Properties editor, select the SNMP tab. To override Grid settings, click Override in the Grid Member Properties editor.
Complete the following in the SNMP tab. For an HA member, click Override Node 2 settings to enter information for node 2 of the HA pair.
- sysContact: Enter the name of the contact person for the appliance.
- sysLocation: Enter the physical location of the appliance.
- sysName: Enter the fully qualified domain name of the appliance.
- sysDescr: Enter useful information about the appliance, such as the software version it is running.
Save the configuration and click Restart if it appears at the top of the screen.

Defining Thresholds for Traps

Threshold events for appliance performance are configurable. For each event, you can set a value that triggers the appliance to send a trap and another value at which the appliance sends a CLEAR trap. The appliance sends a CLEAR trap the first time the event value reaches the reset value after it reached the trigger value.
To define the threshold values:

Grid: From the Grid tab, select the Grid Manager tab, and then select Grid Properties -> Edit from the Toolbar. Member: From the Grid tab, select the Grid Manager -> Members tab -> member, and then click the Edit icon.
In the Grid Properties or Grid Member Properties editor, click Toggle Advanced Mode, and then select the SNMP Threshold tab. To override Grid settings, click Override in the Grid Member Properties editor.
Complete the following in the SNMP Threshold tab. Each of the following event types have default Trigger and Reset values. You can change the values for any of them. You can set SNMP thresholds above or below which the appliance sends SNMP traps and email notifications, if configured to do so. When any allocated usage exceeds the Trigger value, the appliance sends an SNMP trap and email notification to the designated destination, and the status icon for that usage turns red. When usage drops to the Reset value, the status color goes back to normal and turns green.
- CPU Usage: The percentage of the CPU that is currently in use. The default Trigger value is 81%, and the default Reset value is 70%. Note that these default values are set to disable the CPU usage trap. You can enable this trap and configure the trigger and reset values using the CLI command set thresholdtrap.
- Database Objects: The percentage of database capacity that is currently in use. The default Trigger value is 80%, and the default Reset value is 70%.
- Disk: The percentage of the primary hard disk that is currently in use. The default Trigger value is 85%, and the default Reset value is 70%.
- File Distribution Usage: The percentage of the file distribution storage capacity that is currently in use on the selected member. The default Trigger value is 90%, and the default Reset value is 70%.
- IPAM Utilization: For a network, this is the percentage based on the IP addresses in use divided by the total addresses in the network and for a network container that contains subnets, this is the percentage of the total address space defined within the container regardless of whether any of the IP addresses in the subnets are in use. The default Trigger value is 95% and the default Reset value is 85%. The status icon turns red when utilization crosses the configured trigger value. When utilization is below the trigger value, the status color turns blue.
- Memory: The percentage of the system memory that is currently in use. The default Trigger value is 90%, and the default Reset value is 80%.
- Network Capacity: When the Grid is part of a Master Grid, this is the percentage of the Master Grid's network capacity that is used by the Grid's networks. The default Trigger value is 85% and default Reset value is 75%.
- Recursive Clients: The percentage of the limit of concurrent recursive queries. The default Trigger value is 80%, and the default Reset value is 30%. You must also enable the recursive client limit in order for the appliance to send recursive client traps. For information about how to set this limit, see Restricting Recursive Client Queries . When you configure the Trigger and Reset values, ensure that you do not set them too low or too close together. If the Trigger and Reset values are too close together, the appliance may send excessive traps and email notifications because both trigger and reset traps are sent based on the calculated value of simultaneous recursive client queries. For example, when you set the recursive client limit at 50, Trigger value at 71%, and Reset value at 70%, the value for simultaneous recursive client queries is calculated at 50 x .71 = 35 (integer math truncation) and 50 x .70 = 35. This could result in the appliance sending trigger and reset traps for the same value of simultaneous recursive client queries.

- Root File System: The percentage of the root file system ("/") that is currently in use. The default Trigger value is 85%, and the default Reset value is 70%.
- Swap Usage: The percentage of the swap area that is currently in use. The factory default Trigger value is 20% and the factory default Reset value is 10%. The swap usage threshold varies based on the appliance models. The Infoblox GUI displays zero for both the Trigger and Reset values indicating the optimized usage of platform specific default values. The swap usage threshold is set to 50% for 2 GB appliances and 20% for all other appliances. For information about available memory on each appliance model, see Table 39.1 .
- Reporting: The number of reports created on the system that can trigger an SNMP trap. The default Trigger value is 85, and the default Reset value is 70. Note that the maximum number of reports supported per Grid is 300. This field is displayed only when you have configured a reporting server.
- Reporting Volume: The percentage of data transmissions to the reporting server. The default Trigger value is 80%, and the default Reset value is 71%. This field is displayed only when you have configured a reporting server.
- Threat Protection Dropped Traffic: The percentage of packets dropped based on the threat protection rule configuration. The default Trigger value is 90%, and the default Reset value is 70%. This field is displayed only when Threat Protection licenses are installed on the appliance. When the percentage of Threat Protection dropped traffic exceeds the Trigger value or drops below the Reset value, the appliance sends an SNMP trap and an email notification — if configured to do so. For information about setting SNMP traps and email notifications, see Setting SNMP and Email Notifications.
- Threat Protection Total Traffic: The percentage of total traffic received (dropped and passed packets) on the external interfaces. The default Trigger value is 90%, and the default Reset value is 70%. This field is displayed only when Threat Protection licenses are installed on the appliance. When the percentage of total Threat Protection traffic exceeds the Trigger value or drops below the Reset value, the appliance sends an SNMP trap and an email notification — if configured to do so. For information about setting SNMP traps and email notifications, see Setting SNMP and Email Notifications.

If you have installed Threat Protection licenses on the appliance and are using the Infoblox feature, Grid Manager displays the following for Trigger events per second and Reset events per second:

- Alert Rate: The number of SNMP traps sent per second when the appliance sends alerts while passing packets based on threat protection rule configuration. The default Trigger value is 1 and the default Reset value is 0.
- Drop Rate: The number of SNMP traps sent per second when the appliance drops packets based on the threat protection rule configuration. The default Trigger value is 1 and the default Reset value is 0.

If you have installed an RPZ license on the NIOS appliance, you can configure the thresholds to monitor the RPZ hit rate in the Response Policy Zones Hit Rate Configuration section. For information, see Configuring Thresholds for RPZ Hit Rate.

4. Save the configuration and click Restart if it appears at the top of the screen.

The following table lists available Infoblox appliance models and their available memory. Note that TE appliances are IB appliances in Grid Manager.
Table 39.1 Overview of Available Memory for Infoblox Appliance Models

Infoblox Appliance Series	Appliance Model	Memory
Cloud Platform Virtual Appliances	CP-V2200	12 GB
	CP-V1400	8 GB
	CP-V800	2 GB
Advanced Appliances	PT-4000-10GE	24 GB
	PT-4000	24 GB
	PT-2205-10GE	64 GB
	PT-2205	64 GB
	PT-2200	12 GB
	PT-1405	32 GB
	PT-1400	8 GB
Network Insight Appliances	ND-4000	64 GB
	ND-2205	64 GB
	ND-2200	24 GB
	ND-1405	32 GB
	ND-1400	16 GB
	ND-805	32 GB
	ND-800	8 GB
Trinzic Appliances	TE-4010	24 GB
	TE-2225	64 GB
	TE-2220	12 GB
	TE-2215	64 GB
	TE-2210	12 GB
	TE-1425	32 GB
	TE-1420	8 GB
	TE-1415	32 GB
	TE-1410	8 GB
	TE-825	16 GB
	TE-820	4 GB
	TE-815	16 GB
	TE-810	2 GB
	TE-100	2 GB
DNS Cache Acceleration Appliances	IB-4030-10GE	10 GB
	IB-4030	24 GB

Setting SNMP and Email Notifications

You can specify the event types that trigger trap and email notifications. To set SNMP trap and email notifications:

Grid: From the Grid tab, select the Grid Manager tab, and then select Grid Properties -> Edit from the Toolbar. Member: From the Grid tab, select the Grid Manager -> Members tab -> member, and then click the Edit icon.
In the Grid Properties or Grid Member Properties editor, click Toggle Advanced Mode, and then select the Notification tab. To override Grid settings, click Override in the Grid Member Properties editor.
Complete the following:
- Enable All SNMP Notifications: Select this check box if you want the appliance to send SNMP notifications (traps) for all events to the configured trap receivers. This is selected by default. To send SNMP notifications for specific events to the configured trap receiver, select the check box for respective event type.
  For information on configuring trap receivers, see Adding Trap Receivers.
- Enable All Email Notifications: Select this check box if you want the appliance to send email notifications (traps) for all events to the configured email recipients. This is deselected by default. To send email notifications for specific events to the configured email recipients, select the check box for each respective event type. For more information, see Selecting SNMP and Email Notification Types. For information on enabling email notifications and specifying recipients, see Notifying Administrators.
- Alternatively, you can select specific event types from the table, and specify whether you want the appliance to send SNMP Notifications and Email notifications for each type of event.

4. Save the configuration and click Restart if it appears at the top of the screen.

Selecting SNMP and Email Notification Types

Instead of enabling and receiving SNMP and email notifications for all hardware and software events, you can select specific alert types when a specific hardware or software encounters issues. To enable SNMP or email notifications for specific event types, select the corresponding check boxes in the Notification tab of the Grid Properties or Member Properties editor. The following table lists the event types you can select:

Table 39.2 Event Types

Event Type	Description	Sample SNMP Trap
BGP	Sends notifications when the BGP software has failed. For more information, see ibProbableCause Values (OID 3.1.1.1.2.4.0)	2012-11-22 04:49:06 eng-lab-883.inca.infoblox.com [UDP: [10.35.3.115]:38185->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (45366) 0:07:33.66 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.2 IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.115" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: bgp IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibRevokedLicense(53) IB-TRAP-MIB::ibTrapDesc.0 = STRING: An BGP routing daemon failure has occurred.
Backup	Sends notifications about the status of backup operation. For more information, see Processing and Software Failure Traps.	2011-09-22 09:14:17 ib-10-34-41-4.infoblox.com [UDP: [10.34.41.4]:41243->[10.34.41.4]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (48621) 0:08:06.21 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.41.4" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: scheduled_tftp_backups IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibBackupSoftwareFailure(29) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Backup failed.
BloxTools	Sends notifications about the status of bloxTools. For more information, see Object State Change Traps.	2011-09-13 20:38:46 10.34.42.4 [UDP: [10.34.42.4]:38187->[10.34.42.2]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (742156) 2:03:41.56 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.42.4" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: bloxTools IB-TRAP-MIB::ibPreviousState.0 = INTEGER: bloxtools-service-failed(41) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: bloxtools-service-working(39) IB-TRAP-MIB::ibTrapDesc.0 = STRING: BloxTools Service is working.
CPU	Sends notifications about the status of CPU usage. For more information, see Threshold Crossing Traps.	2012-04-12 01:54:59 eng-lab-631.inca.infoblox.com [UDP: [10.35.2.119]:42546->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (786308) 2:11:03.08 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.3 IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.2.119" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibObjectName.0 = STRING: cpu_usage IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 51 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 5 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 3 IB-TRAP-MIB::ibTrapDesc.0 = STRING: CPU usage above threshold value.
CaptivePortal	Sends notifications about the Captive Portal service. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0)	2016-01-08 02:58:23 10.35.107.4 [UDP: [10.35.107.4]:45111->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (22280) 0:03:42.80 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.107.4" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: captive_portal IB-TRAP-MIB::ibPreviousState.0 = INTEGER: captive-portal-service-inactive(51) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: capative-portal-service-working(49) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Captive Portal Service is working.
Cisco ISE	Sends notifications about the status of the Cisco ISE service. For more information, see Object State Change Traps.	2016-01-07 22:26:19 10.40.240.111 [UDP: [10.40.240.111]:47355->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16384) 0:02:43.84 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.40.240.111" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: cisco_ise_server IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 124 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 123 IB-TRAP-MIB::ibTrapDesc.0 = STRING: CiscoISE server 10.36.141.15 is OK.
Clear	Sends notifications when the SNMP trap is cleared. When you select the check box, the CLEAR trap is sent for the following software failures: LDAP servers, OCSP responders, LCD, Serial Console, OSPF, OSPF6, BGP, HSM, Controld, SSH, HTTP, Cluster, Login, and Duplicate IP. For file distribution, the trap is sent when the service is restored. If you deselect the check box, the CLEAR trap is not sent when any of the mentioned software fails. For more information, see Processing and Software Failure Traps.	2015-11-12 22:46:21 10.35.124.1 [UDP: [10.35.124.1]:48446->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (12793) 0:02:07.93 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.124.1" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Login IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibClear(0) IB-TRAP-MIB::ibTrapDesc.0 = STRING: SNMP Trap is cleared. GUI Login
Cloud API	Sends notifications about whether the Cloud API service is functioning or not. for information about Cloud Network Automation, see Introduction to Cloud Network Automation.	2014-11-13 00:52:37 10.35.114.10 [UDP: [10.35.114.10]:57772->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (480221) 1:20:02.21 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.114.10" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: cloud_api IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 105 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 103 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Cloud API service is working.
Cluster	Sends notifications about the status of NIOS clusterd process. For more information, see Processing and Software Failure Traps.	2011-12-10 09:43:23 infoblox.localdomain [UDP: [10.35.2.70]:44193->[10.35.2.70]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (47140) 0:07:51.40 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "0" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Clusterd_Monitor IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibFDSoftwareFailure(32) IB-TRAP-MIB::ibTrapDesc.0 = STRING: WATCHDOG: A grid daemon failure has occurred on 10.35.2.70
Controld	Sends notifications about the NIOS controld process. For more information, see Processing and Software Failure Traps.	2012-08-17 05:29:30 <UNKNOWN> [UDP: [10.32.2.80]:43475->[10.32.2.80]:162]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (24722) 0:04:07.22 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "192.168.1.2" IB-TRAP MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: controld IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibControldSoftwareFailure(11) IB-TRAP-MIB::ibTrapDesc.0 = STRING: A controld failure has occurred.
DHCP	Sends notifications about the status of DHCP service. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2016-04-18 02:42:36 10.35.139.15 [UDP: [10.35.139.15]:35531->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (8809) 0:01:28.09 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.139.15" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: dhcpd IB-TRAP-MIB::ibPreviousState.0 = INTEGER: dhcp-service-inactive(48) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: dhcp-service-working(45) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DHCP Service is working.
DNS	Sends notifications about the status of DNS service. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2016-01-08 01:10:53 10.35.3.154 [UDP: [10.35.3.154]:59876->[10.120.20.12]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (324160) 0:54:01.60 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.154" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING:DNS IB-TRAP-MIB::ibPreviousState.0 = INTEGER: dns-service-working(32) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: dns-service-inactive(34) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS Service is inactive.
DNS Attack	Sends notifications about the status of the DNS attacks. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2016-01-07 23:55:56 10.35.3.201 [UDP: [10.35.3.201]:33199->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (25100) 0:04:11.00 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.201" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: DNSAttack IB-TRAP-MIB::ibPreviousState.0 = INTEGER: dns-attack-active(115) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: dns-attack-inactive(116) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS attack conditions have ended.
DNS Integrity Check	Sends notifications about whether DNS integrity check is functioning or not. For information about DNS integrity check, see About DNS Integrity Check for Authoritative Zones.	2014-06-03 05:35:45 10.34.82.121 [UDP: [10.34.82.121]:42577->[10.120.20.232]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (427200) 1:11:12.00 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.154.3" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibSubsystemName.0 = STRING: DNS Integrity Check IB-TRAP-MIB::ibProbableCause.0 =INTEGER: ibDNSIntegrityCheckNameserversFailed(102) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS Integrity Check is unable to connect to any name servers required to perform the check. There are list of nameservers failure: (['10.35.0.56'])
DNS Integrity Check Connection	Sends notifications about whether DNS integrity check connection is functioning or not. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	016-01-12 05:10:27 10.35.129.15 [UDP: [10.35.129.15]:35201->[10.120.20.12]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (213856) 0:35:38.56 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeN ame.0 = STRING: "10.35.129.15" IB-TRAP-MIB::ibTrapSeverity.0= INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: DNS Integrity Check IB-TRAP-MIB: :ibPreviousState.0 = INTEGER: dns-integrity-check-severity-indetermined(97) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: dns-integrity-check-severity-informational( 99) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS Integrity Check severity has changed. For DNS zone 'default-com.info', severity has changed from 'NONE' to 'INFORMATIONAL'. Reason: While checking server ib-10-35-133-2.infoblox.com.(ipv4=10.35.133.2) INFORMATIONAL discrepancy found because our servers have record(s): info.com. I N NS ib-10-35-12
Database	Sends notifications about the database status. For more information, see Processing and Software Failure Traps.	2013-04-05 02:27:01 10.35.116.2 [UDP: [10.35.116.2]:45332->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (120021) 0:20:00.21 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.116.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: db_usage IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 1 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 85 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 0 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Database capacity used is OK.
Disconnected Grid	Sends notifications about whether a Grid has been disconnected from the Master Grid. For more information, see Object State Change Traps.	2011-12-27 23:38:44 eng-lab-089.inca.infoblox.com [UDP: [10.35.0.89]:53010->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (1049) 0:00:10.49 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.0.89" IB-TRAP-MIB::ibObjectName.0 = STRING: ID_Grid IB-TRAP-MIB::ibPreviousState.0 = INTEGER: grid-disconnected(5) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: grid-connected(4) IB-TRAP-MIB::ibTrapDesc.0 = STRING: The grid member is connected to the grid master.
Discovery	Sends notifications about the discovery status. For information about the Discovery feature, see Infoblox Network Insight.	2013-10-22 01:35:53 eng-lab-302.inca.infoblox.com [UDP: [10.35.1.46]:57126->[10.120.20.102]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (122717) 0:20:27.17 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.1.46" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: discovery_collector IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 89 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 86 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Discovery Collector Service is working.
Discovery Conflict	Sends notifications about conflicts between the DHCP address and the existing IP address. For more information, see Processing and Software Failure Traps.	2014-06-20 00:48:06 10.34.125.2 [UDP: [10.34.125.2]:36159->[10.120.20.232]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (2241) 0:00:22.41 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.125.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: DHCP IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibDHCPHostConflict(66) IB-TRAP-MIB::ibTrapDesc.0 = STRING: DHCP address conflicts with an existing host address.
Discovery Unmanaged	Sends notifications related to the discovery of unmanaged devices and networks. You can configure the maximum number of unmanaged objects the appliance discovers and how often it notifies about these events. For more information about how to configure these parameters, see Defining Seed Routers for Probe Members.	2015-02-09 22:53:57 10.35.103.18 [UDP: [10.35.103.18]:45156->[10.120.20.46]]: DISMAN-EVENT-MIB::sysUpTimeInstance =Timeticks: (46090) 0:07:40.90 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibOperationTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.103.18" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Discovery IB-TRAP-MIB::ibProbableCause.0 =INTEGER: 4012 IB-TRAP-MIB::ibTrapDesc.0 =STRING: New unmanaged devices/networks were found during network discovery process. New unmanaged devices in '10.40.16.0/20' network in 'default' network view.
Disk	Sends notifications about the status of the primary disk. For more information, see Threshold Crossing Traps.	2012-11-22 03:34:32 eng-lab-883.inca.infoblox.com [UDP: [10.35.3.115]:37542->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (87141) 0:14:31.41 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.3 IB-TRAP-MIB::ibNodeName.0 = STRING:"10.35.3.115" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 =STRING: disk_usage IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 15 IB-TRAP-MIB::ibThresholdHigh.0 =INTEGER: 10 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 5 IB-TRAP-MIB::ibTrapDesc.0 = STRING: System primary hard disk usage is over threshold value.
DuplicateIP	Sends notifications when there are duplicate IP addresses. For more information, see ibProbableCause Values (OID 3.1.1.1.2.4.0).	2016-04-18 22:47:38 10.35.139.15 [UDP: [10.35.139.15]:35531->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (7239201) 20:06:32.01 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.139.15" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Equipment IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibDuplicateIPAddressFailure(52) IB-TRAP-MIB::ibTrapDesc.0 = STRING: A Duplicate IP Address has been detected.
ENAT	Sends notifications about the Ethernet port status. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2012-08-27 03:05:25 10.36.3.132 [UDP: [10.36.3.132]:47962->[10.120.20.232]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16624) 0:02:46.24 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.132" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibObjectName.0 = STRING: LAN IB-TRAP-MIB::ibPreviousState.0 = INTEGER: enet-link-up(6) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: enet-link-down(7) IB-TRAP-MIB::ibTrapDesc.0 = STRING: LAN1 port link is down. Please check the connection.
File Distribution Usage	Sends notifications about the HTTP file distribution process. For more information, see Processing and Software Failure Traps.	2016-01-08 01:48:57 10.40.240.113 [UDP: [10.40.240.113]:41443->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (183757) 0:30:37.57 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.40.240.113" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: fd_usage IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibFDSoftwareFailure(42) IB-TRAP-MIB::ibTrapDesc.0 = STRING: File Distribution services storage usage is OK.
FTP	Sends notifications about the status of FTP service. For more information, see Processing and Software Failure Traps.	2016-01-07 23:27:22 10.40.240.113 [UDP: [10.40.240.113]:36063->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (380473) 1:03:24.73 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.40.240.113" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: ftp IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibFTPDSoftwareFailure(44) IB-TRAP-MIB::ibTrapDesc.0 = STRING: An FTPD daemon failure has occurred.
Fan	Sends notifications about the status of the system fan. For more information, see lEquipment Failure Traps.	2012-02-23 23:34:50 10.32.1.222 [UDP: [10.32.1.222]:42742->[10.35.109.24]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (89508) 0:14:55.08 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibEquipmentFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.32.1.222" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: fan IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibFan1Failure(37) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Fan 1 failure has occurred.
HA	Sends notifications about the status of the HA port link. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2014-05-23 00:49:32 eng-lab-589.inca.infoblox.com [UDP: [10.35.2.77]:46426->[10.36.0.200]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (3912) 0:00:39.12 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.20.70" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: HA_Replication IB-TRAP-MIB::ibPreviousState.0 = INTEGER: ha-replication-offline(14) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: ha-replication-online(13) IB-TRAP-MIB::ibTrapDesc.0 = STRING: HA replication is online.
HSM	Sends notifications about the status of the HSM operation. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2016-01-12 20:52:12 10.39.13.77 [UDP: [10.39.13.77]:44962->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (131909) 0:21:59.09 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.39.13.77" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: DNS IB-TRAP-MIB::ibPreviousState.0 = INTEGER: dns-service-working(32) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 55 IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS Service restarted not using HSM
HTTP	Sends notifications about the status of the HTTP service. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2016-01-07 23:16:40 10.40.240.113 [UDP: [10.40.240.113]:36063->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (316247) 0:52:42.47 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.40.240.113" IB-TRAP-MIB::ibTrapSeverity.0= INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: http_file_dist IB-TRAP-MIB::ibPreviousState.0 = INTEGER: http-file-dist-service-inactive(40) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: http-file-dist-service-working(38) IB-TRAP-MIB::ibTrapDesc.0 = STRING: HTTP File Dist Service is working
IFMAP	Sends notifications about the status of the IF-MAP service. For more information, see ibProbableCause Values (OID 3.1.1.1.2.4.0).	2016-04-20 23:40:00 10.34.41.60 [UDP: [10.34.41.60]:33231->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (45256) 0:07:32.56 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.41.60" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: ifmapd IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibIFMAPSoftwareFailure(50) IB-TRAP-MIB::ibTrapDesc.0 = STRING: An IF-MAP server failure has occurred.
IPMI Device	Sends notifications about the status of the IPMI device. For more information, see ibProbableCause Values (OID 3.1.1.1.2.4.0).	2015-03-24 04:10:21 eng-lab-598.inca.infoblox.com [UDP: [10.35.2.86]:56092->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (103490) 0:17:14.90 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibOperationTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.2.86" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibSubsystemName.0 = STRING: IPMI Status Check IB-TRAP-MIB::ibProbableCause.0 = INTEGER: 2105 IB-TRAP-MIB::ibTrapDesc.0 = STRING: IPMI is used by some hardware monitors to test hardware health. The IPMI Device is now available; subsequent hardware monitor failures are likely to be genuine.
IPAM Utilization	Sends notifications about the percentage of IPv4 addresses that are used in a network. For a network container that contains subnets, this indicates the percentage of the total address space defined within the container regardless of whether any of the IP addresses are used in the subnetwork. For more information, see Threshold Crossing Traps.	2014-07-06 19:33:01 eng-lab-514.inca.infoblox.com [UDP: [10.35.2.2]:33413->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (1038846) 2:53:08.46 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.2.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: Threshold IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 0 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 5 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 3 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Network IPAM Utilization capacity usage is OK. Network: 20.0.0.0/29/netview
Load Balancer Device	Sends notifications about whether the LB device is in sync or not. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2013-07-08 02:36:39 10.35.113.2 [UDP: [10.35.113.2]:45568->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (996274) 2:46:02.74 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.113.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: device IB-TRAP-MIB::ibPreviousState.0 = INTEGER: lb-device-down(74) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: lb-device-up(73) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Load Balancer device 10.36.128.1 sync is OK.
LCD	Sends notifications about the status of the LCD process. For more information, see Processing and Software Failure Traps.	2011-12-01 06:31:28 ib-10-35-3-125.infoblox.com [UDP: [10.35.3.125]:56609->[10.35.3.125]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (187334) 0:31:13.34 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.125" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: lcd IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibLCDSoftwareFailure(18) IB-TRAP-MIB::ibTrapDesc.0 = STRING: An LCD failure has occurred.
LDAP Servers	Sends notifications about whether LDAP servers are available or not. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2012-12-17 03:33:58 10.35.106.6 [UDP: [10.35.106.6]:35751->[10.120.20.249]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (4043) 0:00:40.43 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.106.6" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: ldap_servers IB-TRAP-MIB::ibPreviousState.0 = INTEGER: ldap-service-inactive(79) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: ldap-servers-ok(76) IB-TRAP-MIB::ibTrapDesc.0 = STRING: All LDAP servers are available.
License	Sends notifications when the license has been revoked. For more information, see Revoked License Trap.	2014-05-23 00:49:32 eng-lab-589.inca.infoblox.com [UDP: [10.35.2.77]:46426->[10.36.0.200]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (3912) 0:00:39.12 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.6.0 IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.196.165" IB-TRAP-MIB::ibSubsystemName.0 = STRING: vnios IB-TRAP-MIB::ibTrapDesc.0 = STRING: Grid license of member IP 10.34.196.165 with hardware ID 564d5cf2115391ab3f6efee9a9d974aa is revoked. 0 Cold Start
Login	Sends notifications when the login details are incorrect. For more information, see Processing and Software Failure Traps.	2013-04-30 02:56:49 10.34.132.2 [UDP: [10.34.132.2]:35453->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (27604) 0:04:36.04 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.152.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Login IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibGUILoginFailure(58) IB-TRAP-MIB::ibTrapDesc.0 = STRING: A GUI login failure has occurred.
MGM	Sends notifications about the status of the multi-Grid configuration. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2013-04-03 23:48:34 eng-lab-482.inca.infoblox.com [UDP: [10.35.1.226]:37893->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (24697) 0:04:06.97 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.4 IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.116.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibObjectName.0 = STRING: Grid of Grids IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 23 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 24 IB-TRAP-MIB::ibTrapDesc.0 =STRING: Grid connection offline.
MSServer	Sends notifications about the status of Microsoft Servers for Microsoft management. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2013-07-10 03:29:42 10.35.113.2 [UDP: [10.35.113.2]:51679->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (1066392) 2:57:43.92 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.113.2" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: ms_service IB-TRAP-MIB::ibPreviousState.0 = INTEGER: ms-service-down(20) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: ms-service-up(19) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Service connection to Microsoft DNS server 10.102.31.67 is OK.
Memory	Sends notifications about the status of the system memory. For more information, see Threshold Crossing Traps.	2012-04-17 03:09:46 10.35.119.4 [UDP: [10.35.119.4]:37664->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (359835) 0:59:58.35 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.3 IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.119.4" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: memory IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 46 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 50 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 30 IB-TRAP-MIB::ibTrapDesc.0 = STRING: System memory usage is OK.
NTP	Sends notifications about the status of the NTP service. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0)	2013-04-02 23:58:19 10.35.116.6 [UDP: [10.35.116.6]:37505->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (17804) 0:02:58.04 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.1.187" IB-TRAP-MIB::ibObjectName.0 = STRING: ntp_sync IB-TRAP-MIB::ibPreviousState.0 = INTEGER: ntp-sync-down(16) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: ntp-sync-up(15) IB-TRAP-MIB::ibTrapDesc.0 = STRING: The NTP service resumed synchronization.
Network	Sends notifications about the status of the LAN port. For more information, see Threshold Crossing Traps.	2013-01-06 23:52:01 10.35.3.62 [UDP: [10.35.3.62]:49255->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (80879) 0:13:28.79 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.3 IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.62" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: MGM IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 8 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 5 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 3 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Network capacity used is over the threshold value.
OCSP Responders	Sends notifications about the status of OCSP responders. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0).	2016-01-14 03:21:14 10.34.9.91 [UDP: [10.34.9.91]:34663->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (4599) 0:00:45.99 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.9.91" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: ocsp_responders IB-TRAP-MIB::ibPreviousState.0 = INTEGER: ocsp-responders-ok(65) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: ocsp-service-inactive(68) IB-TRAP-MIB::ibTrapDesc.0 = STRING: OCSP service inactive.
OSPF	Sends notifications about the ospfd process. For more information, see Processing and Software Failure Traps.	2012-11-22 04:49:56 eng-lab-883.inca.infoblox.com [UDP: [10.35.3.115]:38185->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (50414) 0:08:24.14 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibTrapOneModule.2 IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.115" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: ospf IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibOSPFSoftwareFailure(35) IB-TRAP-MIB::ibTrapDesc.0 = STRING: An OSPF routing daemon failure has occurred.
OSPF6	Sends notifications about the ospf process for IPv6. For more information, see ibProbableCause Values (OID 3.1.1.1.2.4.0).	2016-01-13 02:03:07 eng-lab-396.inca.infoblox.com [UDP: [10.35.1.140]:45733->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (3970) 0:00:39.70 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.1.140" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: ospf6 IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibClear(0) IB-TRAP-MIB::ibTrapDesc.0 = STRING: SNMP Trap is cleared. OSPF6 SW
PowerSupply	Sends notifications about the status of the power supply. For more information, see lEquipment Failure Traps.	2012-01-20 22:45:01 nextgen.com [UDP: [10.32.111.110]:45323->[10.32.111.110]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (21044) 0:03:30.44 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibEquipmentFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.32.111.110" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: power_supply IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibSystemRestart(61) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Power supply 2 is OK.
RAID	Sends notifications about the RAID array status. For more information, see lEquipment Failure Traps.	2016-01-15 14:30:20 eng-lab-418.inca.infoblox.com [UDP: [10.35.1.162]:57616->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (8737) 0:01:27.37 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibEquipmentFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.1.162" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibObjectName.0 = STRING: raid IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibRAIDIsDegraded(3002) IB-TRAP-MIB::ibTrapDesc.0 = STRING: The system's RAID array is in a degraded state.
Recursive Clients	Sends notifications about whether the DNS recursive server is under flood attacks. For more information, see Threshold Crossing Traps.	2015-01-13 02:05:55 eng-lab-078.inca.infoblox.com [UDP: [10.35.0.78]:55233->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (168817) 0:28:08.17 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.0.78" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: RecursiveClients IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 1 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 800 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 300 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Number of simultaneous DNS recursive lookups is OK.
RIR SWIP	Sends notifications about the status of the RIR SWIP registration. For more information, see ibProbableCause Values (OID 3.1.1.1.2.4.0).	2016-01-11 02:05:17 10.34.11.100 [UDP: [10.34.11.100]:52957->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (43623) 0:07:16.23 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.11.100" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: RIR SWIP IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibRIRSWIPRegistrationFailure(89) IB-TRAP-MIB::ibTrapDesc.0 = STRING: An RIR SWIP registration failure has occurred.CREATE RIR registration request for network "187.0.0.0/24" failed.
Reporting	Sends notifications about the status of the reporting database. For more information, see Threshold Crossing Traps.	2012-01-06 08:59:55 10.35.101.27 [UDP: [10.35.101.27]:59714->[10.35.117.24]]:DISMA N-EVENT-MIB::sysUpTimeInstance = Timeticks: (289200) 0:48:12.00 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.46.6" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: reporting_volume IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 85 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 80 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 71 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Reporting volume usage reached the threshold value.
RPZ Hit Rate	Send Notifications about the percentage of RPZ Hit Rate. For more information, see Threshold Crossing Traps.	2016-04-18 02:52:29 10.35.139.15 [UDP: [10.35.139.15]:35531->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (68173) 0:11:21.73 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.139.15" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibObjectName.0 = STRING: RPZHitRate IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 100 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 1 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 0 IB-TRAP-MIB::ibTrapDesc.0 = STRING: RPZ hit rate is too high: 100%.
RootFS	Sends notifications about the status of the root file system. For more information, see Threshold Crossing Traps.	2011-11-29 06:36:24 ib-10-35-1-144.infoblox.com [UDP: [10.35.1.144]:59707->[10.35.1.144]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (197388) 0:32:53.88 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.1.144" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibObjectName.0 = STRING: rootfs_usage IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 28 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 100 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 90 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Root filesystem disk usage is OK.
SNMP	Sends notifications about the status of the SNMP server. For more information, see Processing and Software Failure Traps.	2012-02-17 06:24:11 eng-lab-630.inca.infoblox.com [UDP: [10.35.2.118]:57802->[10.120.20.174]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (855217) 2:22:32.17 SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::enterprises.7779.3.1.1.1.1.2 SNMPv2-SMI::enterprises.7779.3.1.1.1.2.1.0 = STRING: "10.35.2.118" SNMPv2-SMI::enterprises.7779.3.1.1.1.2.2.0 = INTEGER: 4 SNMPv2-SMI::enterprises.7779.3.1.1.1.2.5.0 = STRING: "snmp" SNMPv2-SMI::enterprises.7779.3.1.1.1.2.4.0 = INTEGER: 13 SNMPv2-SMI::enterprises.7779.3.1.1.1.2.11.0 = STRING: "SNMP Server failure has occurred."
SSH	Sends notifications about the status of the sshd process. For more information, see Processing and Software Failure Traps.	2011-09-21 21:33:17 10.34.42.6 [UDP: [10.34.42.6]:49776->[10.34.42.2]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (6508) 0:01:05.08 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.42.6" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: ssh IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibClear(0) IB-TRAP-MIB::ibTrapDesc.0 = STRING: SNMP Trap is cleared. SSHD SW
SerialConsole	Sends notifications when the serial console login has failed or the admin failed to login to the serial console. For more information, see Processing and Software Failure Traps.	2014-12-15 02:47:59 UDP/IPv6: 2620:10a:6000:2400::8104]:55038 [UDP/IPv6: [2620:10a:6000:2400::8104]:55038]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (501585) 1:23:35.85 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "2620:10a:6000:2400::8104" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Login IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibSerialConsoleLoginFailure(59) IB-TRAP-MIB::ibTrapDesc.0 = STRING: A Serial Console login failure has occurred.
Swap Usage	Sends notifications about whether the swap usage has exceeded the trigger or reset value. For more information, see Defining Thresholds for Traps.	2013-11-25 05:35:56 10.35.129.1 [UDP: [10.35.129.1]:49489->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (24009) 0:04:00.09 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibThresholdCrossingEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.129.1" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibObjectName.0 = STRING: swap_usage IB-TRAP-MIB::ibCurThresholdValue.0 = INTEGER: 100 IB-TRAP-MIB::ibThresholdHigh.0 = INTEGER: 5 IB-TRAP-MIB::ibThresholdLow.0 = INTEGER: 2 IB-TRAP-MIB::ibTrapDesc.0 = STRING: System swap space usage exceeds the critical threshold value.
Syslog	Sends notifications when the syslog process stops. For more information, see Processing and Software Failure Traps.	2016-01-14 01:29:42 10.34.142.105 [UDP: [10.34.142.105]:37566->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (296285) 0:49:22.85 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.34.142.105" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: check_syslog_conf IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibSyslogFailure(67) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Syslog daemon is not running.
System	Sends notifications about the status of the NIOS system. For more information, see Process Started and Stopped Traps.	2014-03-14 05:54:42 eng-lab-636.inca.infoblox.com [UDP: [10.35.2.124]:33232->[10.36.0.200]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (2654067) 7:22:20.67 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.120.17" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: minor(3) IB-TRAP-MIB::ibSubsystemName.0 = STRING: ID_Grid IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibSystemRestart(61) IB-TRAP-MIB::ibTrapDesc.0 = STRING: The system is being restarted.
TAXII	Sends notifications when you start and stop the TAXII service. For more information, see Object State Change Traps.	2016-01-06 20:16:13 eng-lab-242.inca.infoblox.com [UDP: [10.35.0.242]:42213->[10.120.20.21]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (17553) 0:02:55.53 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.0.242" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: taxii IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 122 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 119 IB-TRAP-MIB::ibTrapDesc.0 = STRING: TAXII Service is working.
TFTP	Sends notifications about the status of the TFTP service. For more information, see Processing and Software Failure Traps.	2011-09-16 06:54:08 eng-lab-443.inca.infoblox.com [UDP: [10.35.1.187]:35794->[10.120.20.160]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (50382) 0:08:23.82 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibProcessingFailureTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.1.187" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: critical(5) IB-TRAP-MIB::ibSubsystemName.0 = STRING: tftp IB-TRAP-MIB::ibProbableCause.0 = INTEGER: ibTFTPDSoftwareFailure(27) IB-TRAP-MIB::ibTrapDesc.0 = STRING: A TFTPD daemon failure has occurred.
Threat Analytics	Sends notifications about the status of the Threat Analytics service. For more information, see ibProbableCause Values (OID 3.1.1.1.2.4.0).	2016-01-08 00:19:34 10.35.3.154 [UDP: [10.35.3.154]:59876->[10.120.20.12]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (16184) 0:02:41.84 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.154" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: Threat Analytics IB-TRAP-MIB::ibPreviousState.0 = INTEGER: 127 IB-TRAP-MIB::ibCurrentState.0 = INTEGER: 126 IB-TRAP-MIB::ibTrapDesc.0 = STRING: Threat Analytics Service is working.
Threat Analytics DNS Tunneling	Sends notifications about the DNS tunneling detection. For more information, see ibProbableCause Values (OID 3.1.1.1.2.4.0).	2016-01-08 00:22:07 10.35.3.154 [UDP: [10.35.3.154]:59876->[10.120.20.12]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (31567) 0:05:15.67 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibOperationTrap IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.3.154" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: major(4) IB-TRAP-MIB::ibSubsystemName.0 = STRING: Software IB-TRAP-MIB::ibProbableCause.0 = INTEGER: 4013 IB-TRAP-MIB::ibTrapDesc.0 = STRING: DNS Tunneling detected: The record '*.any.knjuqljsfyyc2t.com' is successfully added into BlackList RPZ zone with comment '[2016-08-01 08:22:06 UTC] [member: infoblox.localdomain] DNS Tunneling' and policy 'No Data'.
Threat Protection	Sends notifications about whether the threat protection service for Infoblox DNS Protection is functioning properly. For more information, see ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0)	2016-04-18 22:48:08 10.35.139.15 [UDP: [10.35.139.15]:54407->[10.120.21.204]]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (3926) 0:00:39.26 SNMPv2-MIB::snmpTrapOID.0 = OID: IB-TRAP-MIB::ibStateChangeEvent IB-TRAP-MIB::ibNodeName.0 = STRING: "10.35.139.15" IB-TRAP-MIB::ibTrapSeverity.0 = INTEGER: info(2) IB-TRAP-MIB::ibObjectName.0 = STRING: threat_protection IB-TRAP-MIB::ibPreviousState.0 = INTEGER: threat-protection-service-inactive(93) IB-TRAP-MIB::ibCurrentState.0 = INTEGER: threat-protection-service-inactive(93) IB-TRAP-MIB::ibTrapDesc.0 = STRING: Threat Protection Service is inactive.

Testing the SNMP Configuration

After you configure SNMP on the appliance, you can do the following to test your SNMP configuration:

From the Grid tab, select the Grid Manager tab -> Members tab -> Grid_member check box, and then select Test SNMP from the Toolbar.

The appliance sends a “test trap” string to the trap receiver and displays a confirmation message at the top of the screen if your SNMP configuration is properly set up. If your SNMP configuration is not complete or if it is invalid, the appliance displays an error message. You can check your configuration and try again.

The following is a sample test trap that the trap receiver can get:

2011-04-04 17:37:14 10.32.2.80 [UDP: [10.32.2.80]:49244->[10.32.2.80]]:

SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-MIB::snmpTrapOID

SNMPv2-MIB::sysName.0 = STRING: 'Test trap'

Browser not supported