In addition to implementing its own enterprise MIBs, Infoblox supports the standard MIBs defined in RFC-41213, Management Information Base for Network Management of TCP/IP-based internets: MIB-II.
The Infoblox MIBs are part of a universal hierarchical structure, usually referred to as the MIB tree. The MIB tree has an unlabeled root with three subtrees. The below figure illustrates the branch of the MIB tree that leads to the Infoblox enterprise MIBs. Each object in the MIB tree has a label that consists of a textual description and an OID (object identifier). An OID is a unique dotted-decimal number that identifies the location of the object in the MIB tree. Note that all OIDs begin with a dot (.) to indicate the root of the MIB tree.
As shown in the figure below, Infoblox is a branch of the Enterprise subtree. IANA (Internet Assigned Numbers Authority) administers the Enterprise subtree, which is designated specifically for vendors who define their own MIBs. The IANA-assigned enterprise number of Infoblox is 7779; therefore, the OIDs of all Infoblox MIB objects begin with the prefix .1.3.6.1.4.1.7779. In addition, IB-DNSSERV and IB-DHCPSERV are branches of the Enterprise subtree as well.
The Infoblox SNMP subtree branches down through two levels, ibProduct and ibOne, to the Infoblox MIBs: ibTrap, ibPlatformOne, ibDNSone, and ibDHCPOne. The ibTrap MIB defines the traps that NIOS appliances send, and the ibPlatformOne, ibDNSone, and ibDHCPOne MIBs provide information about the appliance. For detailed information about these MIBS, see the Infoblox MIBs section.

MIB Hierarchy

MIB Objects

The Infoblox MIB objects were implemented according to the guidelines in RFCs 1155 and 2578. They specify two types of macros for defining MIB objects: OBJECT-TYPE and NOTIFICATION-TYPE. These macros contain clauses that describe the characteristics of an object, such as its syntax and its status. OBJECT-TYPE macros describe MIB objects, and NOTIFICATION-TYPE macros describe objects used in SNMP traps.
Each object in the ibPlatformOne, ibDNSone, and ibDHCPOne MIBs contains the following clauses from the OBJECT-TYPE macro:

OBJECT-TYPE: Provides the administratively-assigned name of the object.

SYNTAX: Identifies the data structure of the object, such as integers, counters, and octet strings.
MAX-ACCESS: Identifies the type of access that a management station has to the object. All Infoblox MIB objects provide read-only access.
STATUS: Identifies the status of the object. Values are current, obsolete, and deprecated.
DESCRIPTION: Provides a textual description of the object.
INDEX or AUGMENTS: An object that represents a conceptual row must have either an INDEX or AUGMENTS clause that defines a key for selecting a row in a table.
OID: The dotted decimal object identifier that defines the location of the object in the universal MIB tree.

The ibTrap MIB defines the SNMP traps that a NIOS appliance can send. Each object in the ibTrap MIB contains the following clauses from the NOTIFICATION-TYPE macro:

NOTIFICATION-TYPE: Provides the administratively-assigned name of the object.

OBJECTS: Provides an ordered list of MIB objects that are in the trap.
STATUS: Identifies the status of the object. Values are current, obsolete, and deprecated.
DESCRIPTION: Provides the notification information.

System Object IDs

Infoblox uses the SNMP system object identifier sysObjectID to identify Infoblox appliances. The following table is a definition of sysObjectID from the SNMPv2 MIB, Management Information Base (MIB) for the Simple Network Management Protocol (SNMP):

OBJECT-TYPE	sysObjectID
SYNTAX	Object Identifier
MAX-ACCESS	read-only
STATUS	current
DESCRIPTION	"The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. For example, if vendor `Flintstones,Inc.' was assigned the subtree 1.3.6.1.4.1.424242, it could assign the identifier 1.3.6.1.4.1.424242.1.1 to its `Fred Router'."

The following table lists the enterprise IDs and their corresponding Infoblox hardware platforms that an SNMP query can return when you request the sysObjectID value. Note that the IDs shown in the table do not include 1.3.6.1.4.1.7779.1. (the infobloxProducts prefix).

sysObjectID for Infoblox Hardware

ID	Description	Definition

ID	Description	Definition
1000	ibDefault	Default environments, such as chroot
1002	ibCisco	Cisco servers
1003	ibvm	vNIOS appliances on VMware ESX or ESXi servers
1004	ibvnios	Virtual NIOS
1401	ib810	Trinzic 810 appliances
1402	ib820	Trinzic 820 appliances
1403	ib1410	Trinzic 1410 appliances
1404	ib1420	Trinzic 1420 appliances
1405	ib1400	Trinzic Reporting 1400 appliances
1406	ib800	Trinzic Reporting 800 appliances
1411	ib2200	Trinzic Reporting 2200 appliances
1412	ib2210	Trinzic 2210 appliances
1413	ib2220	Trinzic 2220 appliances
1423	ib4000	Infoblox-4000 appliances
1431	ib100	Trinzic 100 appliances
1444	nd4000	Network Insight 4000 appliances
1501	ib815	Trinzic 815 appliances
1502	ib825	Trinzic 825 appliances
1503	ib1415	Trinzic 1415 appliances
1504	ib1425	Trinzic 1425 appliances
1505	ib1405	Trinzic 1405 appliances
1506	ib805	Trinzic 805 appliances
1507	pt1405	Advanced 1405 appliances
1511	ib2205	Trinzic 2205 appliances
1512	ib2215	Trinzic 2215 appliances
1513	ib2225	Trinzic 2225 appliances
1514	pt2205	Advanced 2205 appliances
1521	ib4015	Trinzic 4015 appliances
1522	ib4035	Trinzic 4035 appliances
1523	ib4005	Trinzic 4005 appliances
1524	pt4005	Advanced 4005 appliances
1525	ib4025	Trinzic 4025 appliances
1541	nd805	Network Insight 805 appliances
1542	nd1405	Network Insight 1405 appliances
1543	nd2205	Network Insight 2205 appliances
1544	nd4005	Network Insight 4005 appliances

Infoblox MIBs

You can configure a NIOS appliance as an SNMP-managed device so that an SNMP management station can send queries to the appliance and retrieve information from its MIBs. Perform the following tasks to access the Infoblox MIBs:

Configure a NIOS appliance to accept queries, as described in Configuring SNMPv3 Users, see Configuring SNMP.
Load the MIB files onto the management system. To obtain the latest Infoblox MIB files:
1. From the Data Management tab, select the Grid tab -> Grid Manager tab, and then select Download -> SNMP MIBs from the Toolbar.
2. In the Save As dialog box, navigate to a directory to which you want to save the MIBs.
3. Click Save.

Use a MIB browser or SNMP management application to query the objects in each MIB.

The NIOS appliance allows read-only access to the MIBs. This is equivalent to the Get and Get Next operations in SNMP.

Loading the Infoblox MIBs

If you are using an SNMP manager toolkit with strict dependency checking, you must download the following Infoblox MIBs in the order they are listed:

IB-SMI-MIB.txt
IB-TRAP-MIB.txt
IB-PLATFORMONE-MIB.txt
IB-DNSONE-MIB.txt
IB-DHCPONE-MIB.txt
IB-DNSSERV-MIB.txt
IB-DHCPSERV-MIB.txt
IB-DHCPV6ONE-MIB.txt

In addition, if the SNMP manager toolkit you use requires a different MIB file naming convention, you can rename the MIB files accordingly.

NET-SNMP MIBs

NIOS appliances support NET-SNMP (formerly UCD-SNMP), a collection of applications used to implement the SNMP protocol. The NET-SNMP MIBs provide the top-level infrastructure for the SNMP MIB tree. They define, among other things, the objects in the SNMP traps that the agent sends when the SNMP engine starts and stops. For information about NET-SNMP and the MIB files distributed with NET-SNMP, refer to http://net-snmp.sourceforge.net/ .
For SNMP traps to function properly, you must download the following NET-SNMP MIBs directly from http://net-snmp.sourceforge.net/docs/mibs

NET-SNMP-MIB
UCD-SNMP-MIB

Note

Ensure that you save the MIBs as text files in the directory to which you save all the other MIB files.

BGP4 MIB

Infoblox supports BGP4 (Border Gateway Protocol) for DNS anycast addressing. BGP is configured to send SNMP traps to neighboring routers, as defined in RFC4273DefinitionsofManagedObjectsforBGP-4. You must enable and configure the SNMP trap receiver on the Grid member for the member to send SNMP traps.
The BGP protocol service is configured to send SNMP queries about BGP runtime data. The information is returned using the following OIDs and definitions:

OID	Definition

OID	Definition
1.3.6.1.2.1.15.900.1.1	Number of peers
1.3.6.1.2.1.15.900.1.2	Number of active peers
1.3.6.1.2.1.15.900.1.3	Number of AS path entries
1.3.6.1.2.1.15.900.1.4	Number of BGP community entries
1.3.6.1.2.1.15.900.1.5	Total number of prefixes

For each configured BGP peer (a, b, c, d), the information is returned using the following OIDs and definitions:

OID	Definition

OID	Definition
1.3.6.1.2.1.15.900.1.9.a.b.c.d.1	IP address: same as a.b.c.d
1.3.6.1.2.1.15.900.1.9.a.b.c.d.2	State: 0=down, 1=up
1.3.6.1.2.1.15.900.1.9.a.b.c.d.3	ASN
1.3.6.1.2.1.15.900.1.9.a.b.c.d.4	Prefixes
1.3.6.1.2.1.15.900.1.9.a.b.c.d.5	Up/Down time

ibTrap MIB

NIOS appliances send SNMP traps when events, internal process failures, or critical service failures occur. The ibTrap MIB defines the types of traps that a NIOS appliance sends and the value that each MIB object represents. The Infoblox SNMP traps report objects which the ibTrap MIB defines. The below figure illustrates the ibTrap MIB structure. It provides the OID and textual description for each object.

Note

OIDs shown in the illustrations and tables in this section do not include the prefix .1.3.6.1.4.1.7779.

The ibTrap MIB comprises two trees, ibTrapOneModule and ibNotificationVarBind. The ibTraponeModule tree contains objects for the types of traps that a NIOS appliance sends. The ibNotificationVarBind tree contains objects that the Infoblox SNMP traps report. You cannot send queries for the objects in this MIB module. The objects are used only in the SNMP traps.

ibTrapOne MIB Structure

Interpreting Infoblox SNMP Traps

Depending on the SNMP management application your management system uses, the SNMP traps you receive may list the OIDs for all relevant MIB objects from both the ibTrapOneModule and ibNotificationVarBind trees. For OIDs that have string values, the trap lists the text. For OIDs that contain integers, you can use the tables in this section to find out the values. Some SNMP management applications list only the object names and their corresponding values in the SNMP traps. Whether or not your SNMP management application lists OIDs, you can use the tables in this section to find out the corresponding value and definition for each MIB object.

The following is a sample trap a NIOS appliance sends:

418:Jan 31 18:52:26 (none) snmptrapd[6087]: 2008-01-31 18:52:26 10.35.1.156 [UDP:

[10.35.1.156]:32772]: DISMAN-EVENT-MIB::sysUpTimeInstance = Timeticks: (1080)

0:00:10.80 SNMPv2-MIB::snmpTrapOID.0 = OID: SNMPv2-SMI::enterprises.7779.3.1.1.1.1.4.0

SNMPv2-SMI::enterprises.7779.3.1.1.1.2.1.0 = STRING: "10.35.1.156"

SNMPv2-SMI::enterprises.

7779.3.1.1.1.2.3.0 = STRING: "ntp_sync" SNMPv2-SMI::enterprises.7779.3.1.1.1.2.9.0 =

INTEGER: 15 SNMPv2-SMI::enterprises.7779.3.1.1.1.2.10.0 = INTEGER: 16

SNMPv2-SMI::enterprises.7779.3.1.1.1.2.11.0 = STRING: "The NTP service is out of

synchronization."

The sample trap lists the OIDs and their corresponding values that can help you identify the cause of an event or problem. To identify the possible cause and recommended actions for the trap, use the ibTrapDesc tables.

You can interpret the sample trap as follows:

Using the ibTrapOneModule table, you find out OID 7779.3.1.1.1.1.4.0 represents an Object State Change trap. This trap includes the following objects: ibNodeName, ibOjectName, ibPreviousState, ibCurrentState, and ibtrapDesc. For each object, the trap displays the OID and its corresponding value. The following is how you can interpret the rest of the trap:

ibNodeName (OID 7779.3.1.1.1.2.1.0)
- Using the ibNotificationVarBind (OID 3.1.1.1.2) table, you find out OID 7779.3.1.1.1.2.1.0 represents the MIB object ibNodeName, which is the IP address of the appliance on which the trap occurred. Therefore, the statement "7779.3.1.1.1.2.1.0 = STRING: "10.35.1.156" SNMPv2-SMI::enterprises." tells you the IP address of the appliance on which the trap occurred.
ibObjectName (OID 7779.3.1.1.1.2.3.0)
- The statement "7779.3.1.1.1.2.3.0 = STRING: "ntp_sync" SNMPv2-SMI::enterprises." tells you the MIB object ibOjectName, which is the name of the object for which the trap was generated, has a value of "ntp_sync" that indicates NTP synchronization issues.
ibPreviousState (OID 7779.3.1.1.1.2.9.0)
- The statement "7779.3.1.1.1.2.9.0 = INTEGER: 15 SNMPv2-SMI::enterprises." tells you the MIB object ibPreviousState, which indicates the previous state of the appliance, has a value of 15. Using the ibPreviousState and ibCurrentState Values table, you know that 15 represents "ntp-sync-up", which means the NTP server was up and running.
ibCurrentState (OID 7779.3.1.1.1.2.10.0)
- The statement "7779.3.1.1.1.2.10.0 = INTEGER: 16 SNMPv2-SMI::enterprises." tells you the MIB object ibCurrentState, which indicates the current state of the appliance, has a value of 16. Using the ibPreviousState and ibCurrentState Values table, you know that 16 represents "ntp-sync-down", which means the NTP server is now out of sync.
ibTrapDesc (OID 7779.3.1.1.1.2.11.0)
- The last statement "7779.3.1.1.1.2.11.0 = STRING: "The NTP service is out of synchronization." states the description of the trap. Using the Object State Change Traps table for ibTrapDesc, you can find out the trap description and recommended actions for this problem.

Types of Traps (OID 3.1.1.1.1)

ibTrapOneModule defines the types of traps that the NIOS appliance can send. There are five types of SNMP traps.
The table below describe the types of traps and their objects in the ibTrapOneModule tree.

Note

Some SNMP traps for ibThresholdCrossingEvent, ibStateChangeEvent, ibProcStartStopTrap, and ibRevokedLicenseTrap do not have an associated ibProbableCause. The following table lists traps that provide ibProbableCause and those that do not have an ibProbableCause value.

ibTrapOneModule
Trap Binding Variables (OID 3.1.1.1.2)

OID	Trap Type	MIB Object	Description
3.1.1.1.1.1	Equipment Failure	ibEquipmentFailureTrap	The NIOS appliance generates this trap when a hardware failure occurs. This trap includes the following objects: ibNodeName ibTrapSevertiy ibObjectName (equipment name) ibProbableCause ibTrapDesc
3.1.1.1.1.2	Processing and Software Failure	ibProcessingFailureTrap	The NIOS appliance generates this trap when a failure occurs in one of the software processes. This trap includes the following objects: ibNodeName ibTrapSeverity ibSubsystemName ibProbableCause ibTrapDesc
3.1.1.1.1.3	Threshold Crossing	ibThresholdCrossingEvent	The NIOS appliance generates this trap when any of the following events occur: System memory or disk usage exceeds 90%. CPU usage exceeds the trigger value for 15 seconds. A problem occurs when the Grid Master replicates its database to its Grid members. DHCP address usage crosses a watermark threshold. The number or percentage of the DNS security alerts exceeds the thresholds of the DNS security alert triggers. This trap includes the following objects: ibNodeName ibTrapSeverity ibObjectName (threshold name) ibCurThresholdvalue ibThresholdHigh ibThresholdLow ibTrapDesc
3.1.1.1.1.4	Object State Change	ibStateChangeEvent	The NIOS appliance generates this trap when there is a change in its state, such as: The link to one of the configured ports goes down, and then goes back up again. A failover occurs in an HA (high availability) pair configuration. A member connects to the Grid Master. An appliance in a Grid goes offline. This trap includes the following objects: ibNodeName ibTrapSeverity ibObjectName ibPreviousState ibCurrentState ibTrapDesc
3.1.1.1.1.5	Process Started and Stopped	ibProcStartStopTrap	The NIOS appliance generates this type of trap when any of the following events occur: When you enable HTTP redirection. When you change the HTTP access setting. When you change the HTTP session time out setting. When a failover occurs in an HA pair configuration. This trap includes the following objects: ibNodeName ibSubsystemName ibTrapDesc
3.1.1.1.1.6		ibRevokedLicenseTrap	The NIOS appliance generates this trap when a license is revoked. This trap includes the following objects: ibNodeName ibTrapSeverity ibSubsystemName ibTrapDesc
3.1.1.1.1.7		ibOperationTrap	The NIOS appliance generates this trap when a software operation is noteworthy. This trap includes the following objects: ibNodeName ibTrapSeverity ibSubsystemName ibProbableCause ibTrapDesc

Each SNMP trap contains information about the event or the problem. The Infoblox SNMP traps include MIB objects and their corresponding values from the ibNotificationVarBind module. The following table describes the objects in the ibNotificationVarBind module.

The OIDs shown in the following table do not include the prefix ".1.3.6.1.4.1.7779.":

ibNotificationVarBind (OID 3.1.1.1.2)

OID	MIB Object (Type)	Description
3.1.1.1.2.1.0	ibNodeName (DisplayString)	The IP address of the appliance on which the trap occurs. This may or may not be the same as the appliance that sends the trap. This object is used in all types of traps.
3.1.1.1.2.2.0	ibTrapSeverity (Integer)	The severity of the trap. There are five levels of severity. See the Trap Severity table (OID 3.1.1.1.2.2.0) for details below.
3.1.1.1.2.3.0	ibObjectName (DisplayString)	The name of the object for which the trap was generated. This is used in the Equipment Failure traps, Threshold Crossing Event traps, and the Object State Change traps. The following shows what this object represents depending on the type of traps: Equipment Failure traps: The equipment name. Threshold Crossing Event traps: The object name of the trap. State Change traps: The object that changes state.
3.1.1.1.2.4.0	ibProbableCause (Integer)	The probable cause of the trap.
3.1.1.1.2.5.0	ibSubsystemName (DisplayString)	The subsystem for which the trap was generated, such as NTP or SNMP. This object is used in the Processing and Software Failure traps and the Process Start and Stop traps.
3.1.1.1.2.6.0	ibCurThresholdValue (Integer)	The current value of the threshold counter. This object is used in the Threshold Crossing traps.
3.1.1.1.2.7.0	ibThresholdHigh (Integer)	This object is used in Threshold Crossing traps. For CPU usage, this is the trigger value of the SNMP trap. For DHCP address usage, this is the value of the high watermark. This only applies when the appliance sends a trap to indicate that DHCP address usage is above the configured high watermark value for a DHCP address range.
3.1.1.1.2.8.0	ibThresholdLow (Integer)	This object is used in Threshold Crossing traps. For CPU usage, this is the reset value of the SNMP trap. For DHCP address usage, this is the value for the low watermark. This only applies when the appliance sends a trap to indicate that DHCP address usage went below the configured low watermark value for a DHCP address range.
3.1.1.1.2.9.0	ibPreviousState (Integer)	The previous state of the appliance. This object is used in the Object State Change traps. See the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) section for definitions of each value.
3.1.1.1.2.10.0	ibCurrentState (Integer)	The current state of the appliance. This object is used in the Object State Change traps. See the ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0) section for definitions of each value.
3.1.1.1.2.11.0	ibTrapDesc (DisplayString)	The description of the trap. This object is used in all types of traps. See the ibTrapDesc (OID 3.1.1.1.2.11.0) section for the description, possible cause, and recommended actions for each Infoblox SNMP trap.

Trap Severity (OID 3.1.1.1.2.2.0)

The object ibTrapSeverity defines the severity level for each Infoblox SNMP trap. There are five levels of severity:

Value	Description
1	Indetermined [sic]
2	Informational: Event that requires no further action.
3	Minor: Event that does not require user intervention.
4	Major: Event that requires user intervention and assistance from Infoblox Technical Support.
5	Critical: Problem that affects services and system operations, and requires assistance from Infoblox Technical Support.

ibProbableCause Values (OID 3.1.1.1.2.4.0)

The following table lists the values that are associated with the object ibProbableCause (OID 3.1.1.1.2.4.0). These values provide information about the events such as hardware, software for process failures, that trigger SNMP traps.

ibProbableCause Values

Value	OID 3.1.1.1.2.4.0 ibProbableCause	Equipment, Software, or Process Failure Traps
0	ibClear	SNMP Trap is cleared.
1	ibUnknown	An unknown failure has occurred.
2	ibPrimaryDiskFailure	A primary drive failure has occurred.
3	ibFanFailure-old	Unused.
4	ibPowerSupplyFailure	A power supply failure has occurred.
5	ibDBFailure	A database daemon monitoring failure has occurred.
6	ibApacheSoftwareFailure	An apache software failure has occurred.
7	ibSerialConsoleFailure	An Infoblox serial console software failure has occurred.
11	ibControldSoftwareFailure	A controld failure has occurred.
12	ibUpgradeFailure	A system upgrade failure has occurred.
13	ibSNMPDFailure	SNMP Server failure has occurred.
15	ibSSHDSoftwareFailure	An SSH daemon failure has occurred.
16	ibNTPDSoftwareFailure	An NTP daemon failure has occurred.
17	ibClusterdSoftwareFailure	A cluster daemon failure has occurred.
18	ibLCDSoftwareFailure	An LCD daemon failure has occurred.
19	ibDHCPdSoftwareFailure	A DHCP daemon monitoring failure has occurred.
20	ibNamedSoftwareFailure	A named daemon monitoring failure has occurred.
21	ibAuthServerGroupDown	NAC Authentication server group is down.
22	ibAuthServerGroupUp	NAC Authentication server group is up.
24	ibNTLMSoftwareFailure	An NTLM monitoring failure has occurred.
25	ibNetBIOSDaemonFailure	A NetBIOS daemon monitoring failure has occurred.
26	ibWindowBindDaemonFailure	An NT domain service monitoring failure has occurred.
27	ibTFTPDSoftwareFailure	A TFTPD daemon failure has occurred.
28	ibUNUSED28	Unused.
29	ibBackupSoftwareFailure	Backup failed.
30	ibBackupDatabaseSoftwareFailure	Database backup failed.
31	ibBackupModuleSoftwareFailure	Module backup failed.
32	ibBackupSizeSoftwareFailure	File size exceeded the quota. Backup failed.
33	ibBackupLockSoftwareFailure	Another backup is in progress. Backup will not be performed.
34	ibHTTPFileDistSoftwareFailure	An HTTP file distribution daemon failure has occurred.
35	ibOSPFSoftwareFailure	An OSPF routing daemon failure has occurred.
36	ibAuthDHCPNamedSoftwareFailure	An auth named server failure has occurred.
37	ibFan1Failure	Fan 1 failure has occurred.
38	ibFan2Failure	Fan 2 failure has occurred.
39	ibFan3Failure	Fan 3 failure has occurred.
40	ibFan1OK	Fan 1 is OK.
41	ibFan2OK	Fan 2 is OK.
42	ibFan3OK	Fan 3 is OK.
44	ibFTPDSoftwareFailure	An FTPD daemon failure has occurred.
45	ibBloxtoolsSoftwareFailure	A Bloxtools service failure has occurred.
46	ibPowerSupplyOK	The power supply is OK.
47	ibWebUISoftwareFailure	A WebUI software failure has occurred.
48	ibUNUSED48	Unused.
49	ibADAgentSyncFailure	An AD agent client synchronizing domain data failure has occurred.
50	ibIFMAPSoftwareFailure	An IF-MAP server failure has occurred.
51	ibCaptivePortalSoftwareFailure	A Captive Portal service failure has occurred.
52	ibDuplicateIPAddressFailure	A Duplicate IP Address has been detected.
53	ibBGPSoftwareFailure	An BGP routing daemon failure has occurred.
54	ibRevokedLicense	A license has been revoked.
58	ibGUILoginFailure	An admin failed to log in to the GUI.
59	ibSerialConsoleLoginFailure	An admin failed to log in to the serial console.
60	ibSystemReboot	A system reboot was initiated.
61	ibSystemRestart	A system restart was initiated.
62	ibZoneTransferFailure	A zone transfer failure occurred.
63	ibDHCPLeaseConflict	DHCP address conflicts with an existing lease.
64	ibDHCPAddressConflict	DHCP address conflicts with an existing fixed address.
65	ibDHCPRangeConflict	DHCP address conflicts with an existing range.
66	ibDHCPHostConflict	DHCP address conflicts with an existing host.
67	ibSyslogFailure	A syslog daemon failure occurred.
68	ibPowerSupply1Failure	Power supply 1 failure has occurred.
69	ibPowerSupply2Failure	Power supply 2 failure has occurred.
70	ibPowerSupply1OK	Power supply 1 is OK.
71	ibPowerSupply2OK	Power supply 2 is OK.
72	ibReportingTaskSwFailure	A reporting task monitoring failure has occurred.
73	ibReportingDbBackupFailure	A reporting db backup/restore operation failure has occurred.
74	ibFan4Failure	Fan 4 failure has occurred.
75	ibFan5Failure	Fan 5 failure has occurred.
76	ibFan6Failure	Fan 6 failure has occurred.
77	ibFan7Failure	Fan 7 failure has occurred.
78	ibFan8Failure	Fan 8 failure has occurred.
79	ibFan4OK	Fan 4 is OK.
80	ibFan5OK	Fan 5 is OK.
81	ibFan6OK	Fan 6 is OK.
82	ibFan7OK	Fan 7 is OK.
83	ibFan8OK	Fan 8 is OK.
84	ibOSPF6SoftwareFailure	An OSPF6 routing daemon failure has occurred.
85	ibOCSPResponderFailure	OCSP responder failed.
86	ibReportingAlertTriggered	A reporting alert is triggered.
87	ibCapturedQueriesUploadFailure	Upload for captured DNS queries failed.
88	ibLDAPServerFailure	The LDAP server failed.
89	ibRIRWIPRegistrationFailure	RIR SWIP registration failed.
90	ibPowerSupply1Removed	Power supply 1 has been removed.
91	ibPowerSupply2Removed	Power supply 2 has been removed.
92	ibIPMISensorErrorDetected	Error detected on the sensor for the IPMI port (used for LOM)
93	ibDiscoveryConsolidatorTaskSwFailure	Discovery service on the Consolidator failed.
94	ibDiscoveryCollectorTaskSwFailure	Discovery service on probes failed.
95	ibDiscoveryBackupSwFailure	Discovery backup service failed.
96	ibThreatProtectionAutoDownloadFailure	Automatic download of threat protection rule failed.
97	ibThreatProtectionPublishFailure	Threat protection rule publish failed.
98	ibPassiveHANodeARPConnectivityFailure	HA node failed to connect to local router.
99	ibPassiveHANodeARPConnectivitySuccess	HA node successfully connects to local router.
100	ibDNSIntegrityCheckConnectionFailed	Connection between Grid member and Grid Master failed.
101	ibDNSIntegrityCheckPrimaryServersFailed	DNS data (NS RRset) check for Grid primaries failed.
102	ibDNSIntegrityCheckNameserversFailed	DNS data (NS RRset) check for name servers failed.
103	ibCloudAPIFailure	Cloud API service failed.
104	ibRpzRefreshFailure	An RPZ refresh failure has occurred.
105	ibUnboundSoftwareFailure	Unbound software failure has occurred.
106	ibAnalyticsAutoDownloadFailure	Automatic download of analytic module set failed.
107	ibDnsHealthCheckFailed	The DNS health check has failed.
108	ibDnsHealthCheckSucceed	The DNS health check is successful.
109	ibBFDSoftwareFailure	BFD has failed to detect failure in the bidirectional path between two interfaces.
110	ibOutboundWorkerFailed	An Outbound worker has failed.
3001	ibRAIDIsOptimal	The system’s RAID array is now running in an optimal state.
3002	ibRAIDIsDegraded	The system’s RAID array is in a degraded state.
3003	ibRAIDIsRebuilding	The system’s RAID array is rebuilding.
3004	ibRAIDStatusUnknown	Unable to retrieve RAID array state!
3005	ibRAIDBatteryIsOK	The system’s RAID battery is OK.
3006	ibRAIDBatteryFailed	A RAID battery failure has occurred.
3007	ibRAIDOptimalMismatch	The system's RAID array is now running in an optimal state (Mismatched disk(s) found).
3008	ibRAIDDegradedMismatch	The system's RAID array is in a degraded state (Mismatched disk(s) found).
3009	ibRAIDRebuildingMismatch	The system's RAID array is rebuilding (Mismatched disk(s) found).
3010	ibRAIDBatteryWeak	Please replace the system's RAID battery soon.
3011	ibRAIDIsDegradedDisk1	The system's RAID array is in a degraded state. RAID Disk1 is EMPTY.
3012	ibRAIDIsDegradedDisk2	The system's RAID array is in a degraded state. RAID Disk2 is EMPTY.
3013	ibRAIDIsDegradedDisk3	The system's RAID array is in a degraded state. RAID Disk3 is EMPTY.
3014	ibRAIDIsDegradedDisk4	The system's RAID array is in a degraded state. RAID Disk4 is EMPTY.
3015	ibRAIDIsDegradedDisk5	The system's RAID array is in a degraded state. RAID Disk5 is EMPTY.
3016	ibRAIDIsDegradedDisk6	The system's RAID array is in a degraded state. RAID Disk6 is EMPTY.
3017	ibRAIDIsDegradedDisk7	The system's RAID array is in a degraded state. RAID Disk7 is EMPTY.
3018	ibRAIDIsDegradedDisk8	The system's RAID array is in a degraded state. RAID Disk8 is EMPTY.
3019	ibRAIDIsRebuildingDisk1	The system's RAID array is rebuilding. RAID Disk1 is OFFLINE.
3020	ibRAIDIsRebuildingDisk2	The system's RAID array is rebuilding. RAID Disk2 is OFFLINE.
3021	ibRAIDIsRebuildingDisk3	The system's RAID array is rebuilding. RAID Disk3 is OFFLINE.
3022	ibRAIDIsRebuildingDisk4	The system's RAID array is rebuilding. RAID Disk4 is OFFLINE.
3023	ibRAIDIsRebuildingDisk5	The system's RAID array is rebuilding. RAID Disk5 is OFFLINE.
3024	ibRAIDIsRebuildingDisk6	The system's RAID array is rebuilding. RAID Disk6 is OFFLINE.
3025	ibRAIDIsRebuildingDisk7	The system's RAID array is rebuilding. RAID Disk7 is OFFLINE.
3026	ibRAIDIsRebuildingDisk8	The system's RAID array is rebuilding. RAID Disk8 is OFFLINE.
3027	ibRAIDDegradedMismatchDisk1	The system's RAID array is in a degraded state (Mismatched disk(s) found). RAID Disk1 is EMPTY.
3028	ibRAIDDegradedMismatchDisk2	The system's RAID array is in a degraded state (Mismatched disk(s) found). RAID Disk2 is EMPTY.
3029	ibRAIDDegradedMismatchDisk3	The system's RAID array is in a degraded state (Mismatched disk(s) found). RAID Disk3 is EMPTY.
3030	ibRAIDDegradedMismatchDisk4	The system's RAID array is in a degraded state (Mismatched disk(s) found). RAID Disk4 is EMPTY.
3031	ibRAIDDegradedMismatchDisk5	The system's RAID array is in a degraded state (Mismatched disk(s) found). RAID Disk5 is EMPTY.
3032	ibRAIDDegradedMismatchDisk6	The system's RAID array is in a degraded state (Mismatched disk(s) found). RAID Disk6 is EMPTY.
3033	ibRAIDDegradedMismatchDisk7	The system's RAID array is in a degraded state (Mismatched disk(s) found). RAID Disk7 is EMPTY.
3034	ibRAIDDegradedMismatchDisk8	The system's RAID array is in a degraded state (Mismatched disk(s) found). RAID Disk8 is EMPTY.
3035	ibRAIDRebuildingMismatchDisk1	The system's RAID array is rebuilding (Mismatched disk(s) found). RAID Disk1 is OFFLINE.
3036	ibRAIDRebuildingMismatchDisk2	The system's RAID array is rebuilding (Mismatched disk(s) found). RAID Disk2 is OFFLINE.
3037	ibRAIDRebuildingMismatchDisk3	The system's RAID array is rebuilding (Mismatched disk(s) found). RAID Disk3 is OFFLINE.
3038	ibRAIDRebuildingMismatchDisk4	The system's RAID array is rebuilding (Mismatched disk(s) found). RAID Disk4 is OFFLINE.
3039	ibRAIDRebuildingMismatchDisk5	The system's RAID array is rebuilding (Mismatched disk(s) found). RAID Disk5 is OFFLINE.
3040	ibRAIDRebuildingMismatchDisk6	The system's RAID array is rebuilding (Mismatched disk(s) found). RAID Disk6 is OFFLINE.
3041	ibRAIDRebuildingMismatchDisk7	The system's RAID array is rebuilding (Mismatched disk(s) found). RAID Disk7 is OFFLINE.
3042	ibRAIDRebuildingMismatchDisk8	The system's RAID array is rebuilding (Mismatched disk(s) found). RAID Disk8 is OFFLINE.
3043	ibRAIDIsInoperable	The system’s RAID array is inoperable.
3044	ibRAIDPredictedDegraded	The system's RAID array is in a predicted degraded state.
3045	ibRAIDPredictedDegradedDisk1	The system's RAID array is in a predicted degraded state. RAID Disk1 is in such predicted degraded state.
3046	ibRAIDPredictedDegradedDisk2	The system's RAID array is in a predicted degraded state. RAID Disk2 is in such predicted degraded state.
3047	ibRAIDPredictedDegradedDisk3	The system's RAID array is in a predicted degraded state. RAID Disk3 is in such predicted degraded state.
3048	ibRAIDPredictedDegradedDisk4	The system's RAID array is in a predicted degraded state. RAID Disk4 is in such predicted degraded state.
3049	ibRAIDPredictedDegradedDisk5	The system's RAID array is in a predicted degraded state. RAID Disk5 is in such predicted degraded state.
3050	ibRAIDPredictedDegradedDisk6	The system's RAID array is in a predicted degraded state. RAID Disk6 is in such predicted degraded state.
3051	ibRAIDPredictedDegradedDisk7	The system's RAID array is in a predicted degraded state. RAID Disk7 is in such predicted degraded state.
3052	ibRAIDPredictedDegradedDisk8	The system's RAID array is in a predicted degraded state. RAID Disk8 is in such predicted degraded state.
4001	ibDisconnectGridAttachFailed	A disconnected Grid failed to attach to the Master Grid.
4002	ibDisconnectedGridDetachFailed	A disconnected Grid failed to detach from the Master Grid.
4003	ibDisconnectedGridDetachFailedSubgrid Offline	An offline Grid failed to detach from the Master Grid.
4004	ibDisconnectedGridSnapshotFailed	The snapshot operation failed on a disconnected Grid.
4005	ibDnssecAutomaticKSKRolloverApproching	An automatic rollover of the KSK will be performed in seven days.
4006	ibDnssecManualKSKRolloverDueApproching	A manual KSK rollover is due within the next seven days.
4007	ibDnssecAutomaticKSKRolloverDone	The KSK has been automatically rolled over.
4008	ibDnssecManualKSKRolloverDone	The KSK has been manually rolled over.
4009	ibDnssecKSKRolloverOverdue	The KSK rollover is overdue.
4010	ibPortDiscoveryConflict	A port detection conflict has been detected.
4011	ibDeviceDiscoveryConflict	A device detection conflict has been detected.
4012	ibDeviceUnmanaged	New unmanaged devices/networks were found during network discovery process.
4013	ibAnalyticsDnstUpdate	The DNS tunneling detection has occurred.
4014	ibSyslogBackupDone	The syslog backup process is successful.
4015	ibSyslogBackupFailed	The syslog backup process failed.

ibSubsystemName Values (OID 3.1.1.1.2.5.0)

The below table lists the values that are associated with the object ibSubsystemName (OID 3.1.1.1.2.5.0). These values provide information about the subsystems that trigger the traps.

ibSubsystemName Values

Value	OID 3.1.1.1.2.5.0 ibSubsystemName
0	Uses the original ibObjectName and ibSubsystemName when the trap is cleared. The process failure trap is appended to the CLEAR trap descriptions.
1	N/A
2	N/A
3	N/A
4	N/A
5	Db_jnld
6	httpd
7	serial_console
11	controld
12	N/A
13	Snmpd
15	Sshd
16	Ntpd
17	Clusterd
18	Lcd
19	Dhcpd
20	Named
24	NTLM
25	Netbiosd
26	Winbindd
27	Tftpd
29	N/A
30	db_dump
31	N/A
32	Scheduled_backups
33	N/A
34	HTTPd
35	OSPF
36	AuthDhcpNamed
44	ftpd
45	bloxtools
47	webui
50	ifmap
51	captive_portal
53	bgp
58	GUI_Login
72	reporting_service
84	OSPF6
95	Discovery_backups
105	Unbounds
-	HA_Replication
-	HSM Group Status
-	Cluster
-	Cluster_Send_Queue
-	Cluster_Recv_Queue
-	RPZHitRate
-	Authentication Server Group

ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0)

The ibPreviousState object indicates the state of the appliance before the event triggered the trap. The ibCurrentState object indicates the current state of the appliance. These MIB values were introduced in NIOS version 8.6.5.

The following table shows the message and description for each state:

ibPreviousState and ibCurrentState Values

Value	Description	Definition
1	ha-active	The HA pair is in ACTIVE state.
2	ha-passive	The HA pair is in PASSIVE state.
3	ha-initial	The HA pair is in INITIAL state.
4	Grid-connected	The Grid member is connected to the Grid Master.
5	Grid-disconnected	The Grid member is not connected to the Grid Master.
12	service-down	The service is down.
13	ha-replication-online	The HA pair replication is online.
14	ha-replication-offline	The HA pair replication is offline.
15	ntp-syn-up	The NTP server is synchronizing.
16	ntp-syn-down	The NTP server is out of synchronization.
17	ms-server-up	Microsoft server is up.
18	ms-server-down	Microsoft server is down.
19	ms-service-up	Microsoft service connection is active.
20	ms-service-down	Microsoft service connection is inactive.
21	nac-server-group-down	NAC Authentication server group is down.
22	nac-server-group-up	NAC Authentication server group is up.
23	mgm-service-up	MGM service is active.
24	mgm-service-down	MGM service is inactive.
25	ha-active-active	HA Pair is in Dual Active state.
26	ftp-service-working	FTP service is working.
27	ftp-service-failed	FTP service failed.
28	ftp-service-inactive	FTP service is inactive.
29	tftp-service-working	TFTP service is working.
30	tftp-service-failed	TFTP service failed.
31	tftp-service-inactive	TFTP service is inactive.
32	dns-service-working	DNS service is working.
33	dns-service-failed	DNS service failed. Review the syslog file.
34	dns-service-inactive	DNS service is inactive. Check if an administrator disabled the service.
35	ntp-service-working	NTP service is working.
36	ntp-service-failed	NTP service failed.
37	ntp-service-inactive	NTP service is inactive.
38	http-file-dist-service-working	HTTP File Dist service is working.
39	http-file-dist-service-failed	HTTP File Dist service failed.
40	http-file-dist-service-inactive	HTTP File Dist service is inactive.
41	bloxtools-service-working	bloxTools service is working.
42	bloxtools-service-warning	bloxTools service is in warning state.
43	bloxtools-service-failed	bloxTools service failed.
44	bloxtools-service-inactive	bloxTools service is inactive.
45	dhcp-service-working	DHCP service is working. No action required.
46	dhcp-service-warning	DHCP service is in warning state. Review the syslog file.
47	dhcp-service-failed	DHCP service failed. Review the syslog file.
48	dhcp-service-inactive	DHCP service is inactive. Check if an administrator disabled the service.
49	captive-portal-service-working	Captive portal service is working.
50	captive-portal-service-failed	Captive portal service failed.
51	captive-portal-service-inactive	Captive portal service inactive.
52	ifmap-service-working	IF-MAP service is working.
53	ifmap-service-failed	IF-MAP service failed.
54	ifmap-service-inactive	IF-MAP service inactive.
56	hsm-group-down	HSM operation failed.
57	hsm-group-up	HSM operation succeeded.
59	reporting-service-working	Reporting service is working.
60	reporting-service-failed	Reporting service failed.
61	reporting-service-inactive	Reporting service inactive.
62	dns-cache-acceleration-working	DNS cache acceleration is working.
63	dns-cache-acceleration-failed	DNS cache acceleration failed.
64	dns-cache-acceleration-inactive	DNS cache acceleration is inactive.
65	ocsp-responders-ok	All OCSP responders are available.
66	ocsp-responder-failed	At least one OCSP responder has become unavailable.
67	ocsp-responders-unavailable	All OCSP responders are out of service.
68	cas-inactive	Certificate authentication service is inactive.
69	subgrid-attached	In a Multi-Grid configuration, sub Grid is attached to the Master Grid.
70	subgrid-detached	In a Multi-Grid configuration, sub Grid is detached from the Master Grid.
71	snapshot-disabled	In a Multi-Grid configuration, the snapshot of the Grid's current state is disabled.
72	snapshot-enabled	In a Multi-Grid configuration, the snapshot of the Grid's current state is enabled.
73	lb-device-up	Load balancer device is working.
74	lb-device-down	Load balancer device is down.
76	ldap-servers-ok	All LDAP servers are available.
77	ldap-server-failure	At least one LDAP server is unavailable.
78	ldap-servers-unavailable	All LDAP servers are unavailable.
79	ldap-service-inactive	LDAP service is inactive.
80	sgm-state-online	SGM is online.
81	sgm-state-offline	SGM is offline.
82	discovery-consolidator-service-working	Service on discovery the consolidator for Network Insight is working.
83	discovery-consolidator-service-warning	Service on discovery the consolidator for Network Insight is in warning state.
84	discovery-consolidator-service-failed	Service on discovery the consolidator for Network Insight failed.
85	discovery-consolidator-service-inactive	Service on discovery the consolidator for Network Insight is inactive.
86	discovery-collector-service-working	Service on discovery probes for Network Insight is working.
87	discovery-collector-service-warning	Service on discovery probes for Network Insight is in warning state.
88	discovery-collector-service-failed	Service on discovery probes for Network Insight failed.
89	discovery-collector-service-inactive	Service on discovery probes for Network Insight is inactive.
90	threat-protection-service-working	Threat protection service for Infoblox DNS Protection is working.
91	threat-protection-service-warning	Threat protection service for Infoblox DNS Protection is in warning state
92	threat-protection-service-failed	Threat protection service for Infoblox DNS Protection failed.
93	threat-protection-service inactive	Threat protection service for Infoblox DNS Protection is inactive.
94	mgm-external-storage-disabled	MGM external storage is disabled.
95	dns-integrity-check-failed	DNS Integrity check for authoritative zones failed.
96	dns-integrity-check-working	DNS Integrity check for authoritative zones is working.
97	dns-integrity-check-severity-indetermined	DNS Integrity check severity is None.
98	dns-integrity-check-severity-normal	DNS Integrity check severity is NORMAL.
99	dns-integrity-check-severity-informational	DNS Integrity check severity is INFORMATIONAL.
100	dns-integrity-check-severity-warning	DNS Integrity check severity is WARNING.
101	dns-integrity-check-severity-severe	DNS Integrity check severity is SEVERE.
102	dns-integrity-check-severity-critical	DNS Integrity check severity is CRITICAL.
103	cloud-api-service-working	Cloud API service is working.
104	cloud-api-service-failed	Cloud API service failed.
105	cloud-api-service-inactive	Could API service is inactive.
106	dns-service-dtc-failed	DNS sub-feature DNS Traffic Control failed.
107	raid-status-is-unavailable	RAID hardware status is unavailable.
108	raid-status-is-available	RAID hardware status is available again.
109	ipmi-device-warning	IPMI device is not available.
110	ipmi-device-unavailable	IPMI device repeatedly is not available.
111	ipmi-device-available	IPMI device is available again.
112	rpz-refresh-working	RPZ refresh is working.
113	rpz-refresh-failed	RPZ refresh failed.
114	rpz-refresh-unknown	RPZ refresh unknown.
115	dns-attack-active	DNS attack is active.
116	dns-attack-inactive	DNS attack is inactive.
117	high-rpz-hit-rate	RPZ hit rate exceeds the normal value.
118	normal-rpz-hit-rate	RPZ hit rate has returned to normal value.
119	taxii-working	TAXII server is working.
120	taxii-warning	TAXII server is warning.
121	taxii-failed	TAXII server is failed.
122	taxii-inactive	TAXII server is inactive.
123	cisco-ise-server-up	Cisco ISE server is connected.
124	cisco-ise-server-down	Cisco ISE server is not connected.
125	threat-analytics-service-inactive	Threat Analytics service is inactive.
126	threat-analytics-service-working	Threat Analytics service is working.
127	threat-analytics-service-warning	Threat Analytics service is in warning state.
128	threat-analytics-service-failed	Threat Analytics Service is failed.
129	outbound-service-manager-started	OUTBOUND Service Manager is working
130	outbound-service-manager-failed	OUTBOUND Service Manager is failed
131	outbound-service-manager-stopped	OUTBOUND Service Manager is inactive
133	imc-servers-ok	Subscriber Collection Service is working.
134	imc-server-failure	Subscriber Collection Service failed.
135	imc-servers-unavailable	All NAS gateways are unavailable.
136	imc-service-inactive	Subscriber Collection Service is inactive.
137	imc-zvelo-service-unavailable	Initial category information data is downloading.
138	imc-server-initializing	Initial Subscriber Collection service interim interval.
139	dns-service-working-atc-fwd-down	The DNS service is working, but Active Trust Cloud (ATC) forwarding is down.
140	dfp-service-working	The DFP service is working.
141	dfp-service-failed	The DFP service has failed.
142	dfp-service-inactive	The DFP service is disabled.
143	dfp-service-stopped	The DFP service has been stopped by the user.
144	dfp-service-init	The DFP service is initializing.
146	dot-doh-support-inactive	DOT DOH support is inactive
148	imc-bwl-reboot-required	IMC DCA BWlist reboot required
150	dot-doh-reboot-required	DOT/DOH is enabled from the Grid Master; a manual reboot is required by the user.
151	dot-doh-service-working	DOT/DOH service is working.
152	dot-doh-service-inactive	DOT/DOH service is disabled.
160	imc-bwl-support-inactive	The DCA BW list is disabled.
161	imc-bwl-reboot-required	A manual reboot is required after changing the IMC DCA BW configuration.
162	imc-bwl-working	The DCA BW list is working.
163	imc-zvelo-database-update-failed	The IMC Zvelo database update has failed.
164	imc-zvelo-database-expired	The IMC Zvelo database has expired.
165	imc-zvelo-snmp-clear-trap	The IMC Zvelo SNMP clear trap is triggered.
166	cds-working	Cloud DNS Sync is working
167	cds-failed	Cloud DNS Sync is failed
168	cds-initializing	Cloud DNS Sync is initializing
169	cds-inactive	Cloud DNS Sync is disabled

The Grid member running Subscriber Collection Service has a default state of 136 (imc-service-inactive). When Subscriber Collection Service is enabled, it goes to the 138 (imc-server-initializing) state. That is, the service will be enabled but not fully populated until the interim interval expires. Once the interim interval expires, it transitions to the 133 (imc-servers-ok) state unless parental control is enabled. If parental control is enabled, the state changes to 137 (imc-zvelo-service-unavailable) until the category data is downloaded. After this it goes to state 133 (imc-servers-ok). If the collector service is not running, it transitions to state 134 (imc-server-failure).

Trap 136 implies that subscriber collection is not active. Trap 134 implies that the collector is not running. If the monitor is disabled , then trap 136 (imc-service-inactive) is triggered.

ibTrapDesc (OID 3.1.1.1.2.11.0)

The ibTrapDesc object lists the trap messages of all Infoblox SNMP traps. This section lists all the SNMP traps by their trap types. Each trap table describes the trap message, severity, cause, and recommended actions.

lEquipment Failure Traps

ibTrapDesc OID 3.1.1.1.2.11.0	ibTrapSeverity OID 3.1.1.1.2.2	Description/Cause	Recommended Actions
Primary Drive Full
Primary drive is full.	Major	The primary disk drive reached 100% of usage.	Review the syslog file to identify the possible cause of this problem.
Fan Monitoring
Fan <n> failure has occurred.	Minor	The specified fan <n> failed, where <n> indicates the fan number.	Inspect the specified fan for mechanical or electrical problems.
Fan <n> is OK.	Informational	The specified fan <n> is functioning properly, where <n> indicates the fan number.	No action is required.
Power Supply Failure: monitored at 1 minute
A power supply failure has occurred.	Major	The power supply failed.	Inspect the power supply for the possible cause of the failure.
Power supply <n> failure has occurred.	Major	The specified power supply <n> failed, where <n> indicates the power supply number.	Inspect the specified power supply for the possible cause of the failure.
The power supply is OK.	Informational	The power supply is functioning properly.	No action is required.
Power supply <n> is OK.	Informational	The specified power supply <n> is functioning properly, where <n> indicates the power supply number.	No action is required.
RAID monitoring, at 1 minute interval
A RAID battery failure has occurred.	Major	The system RAID battery failed. The alert light is red.	Inspect the battery for the possible cause of the failure.
The system's RAID battery is OK.	Informational	The system RAID battery is charging and functioning properly. The alert light changed from red to green.	No action is required.
Unable to retrieve RAID array state!	Undetermined	The appliance failed to retrieve the RAID array state. The alert light is red.	Review the syslog file to identify the possible cause of this problem.
The system's RAID array is now running in an optimal state.	Informational	The RAID system is functioning at an optimal state.	No action is required.
The system's RAID array is in a degraded state. RAID Disk <n> is EMPTY.	Major	The RAID system is degrading. The specified RAID Disk <n> is empty, where <n> indicates the RAID disk number.	Review the syslog file to identify the possible cause of this problem.
The system's RAID array is rebuilding. RAID Disk <n> is OFFLINE.	Minor	The RAID system is rebuilding. The specified RAID Disk <n> is offline, where <n> indicates the RAID disk number.	No action is required.
Syslog Backup Processes
The syslog backup process is successful.	Informational	Rotated syslog files are uploaded successfully to the external backup server.	No action is required.
The syslog backup process failed.	Major	Failed to forward the rotated syslog files to the external backup server.	Review the syslog messages to identify the possible cause of this problem.

Processing and Software Failure Traps

The ibSubsystemName object is associated with certain traps of the Processing and Software Failure traps.
Therefore, you cannot map all the traps of the Processing and Software Failure traps with the ibSubsystemName. If there is no value in the ibSubsystemName, then it belongs to the N/A category. For more information on the values for the ibSubsystemName, see the ibSubsystemName Values table.

Named Daemon Failure
A named daemon monitoring failure has occurred.	Critical	The named process failed.	Review the syslog file to identify the possible cause of this problem.
DHCP Daemon Failure
A DHCP daemon monitoring failure has occurred.	Critical	The dhcpd process failed.	Review the syslog file to identify the possible cause of this problem.
SSH Daemon Failure
An SSH daemon failure has occurred.	Major	The sshd process failed.	Review the syslog file to identify the possible cause of this problem.
NTP Daemon Failure, monitored every 10 minutes
An NTP daemon failure has occurred.	Major	The ntpd process failed.	Review the syslog file to identify the possible cause of this problem.
Cluster Daemon Failure
A grid daemon failure has occurred.	Critical	The clusterd process failed.	Review the syslog file to identify the possible cause of this problem.
LCD Daemon Failure
An LCD failure has occurred.	Major	The LCD process failed. The alert light is yellow.	Inspect the LCD panel for the possible cause of this problem. Review the syslog file to identify the possible cause of this problem.
Apache Software httpd failure, monitored every 2 minutes
An Apache software failure has occurred.	Critical	The request to monitor the Apache server failed.	Review the syslog file to identify the possible cause of this problem.
Serial Console Failure
An Infoblox serial console software failure has occurred.	Major	The Infoblox serial console failed.	Review the syslog file to identify the possible cause of this problem.
Controld Software Failure
A controld failure has occurred.	Critical	The controld process failed.	Review the syslog file to identify the possible cause of this problem.
SNMP Sub-agent Failure
An SNMP server failure has occurred.	Major	The one-subagent process failed.	Review the syslog file to identify the possible cause of this problem.
TFTPD and FTPD Failure
A TFTPD daemon failure has occurred.	Critical	The tftpd process failed.	Review the syslog file to identify the possible cause of this problem.
An FTPD daemon failure has occurred.	Critical	The ftpd process failed.	Review the syslog file to identify the possible cause of this problem.
HTTP File Distribution, monitored at 10 second intervals
An HTTP file distribution daemon failure has occurred.	Critical	The HTTP file distribution process failed.	Review the syslog file to identify the possible cause of this problem.
DNS ONE quagga Processes (zebra & ospfd)
An OSPF routing daemon failure has occurred.	Critical	Either the zebra process or the ospfd process failed. Both the zebra and ospfd process belongs to ospf subsystem.	Review the syslog file to identify the possible cause of this problem.
Backup Failure
Backup failed.	Minor	The backup failed. One of the following could be the cause of the failure: The appliance could not access a backup directory. The backup was interrupted by one of the following signals: SIGINT, SIGHUP, or SIGTERM. Incorrect login or connection failure in an FTP backup. The backup failed to create temporary files.	Review the syslog file to identify the possible cause of this problem.
Database Backup Failure
Database backup failed.	Not implemented	The db_dump process failed.	Review the syslog file to identify the possible cause of this problem.
Backup Module Failure
Module backup failed.	Not implemented	The backup of product- specific files failed.	Review the syslog file to identify the possible cause of this problem.
Backup File Size Exceeded
File size exceeded the quota. Backup failed.	Not implemented	The backup failed because the file size exceeded the limit of 5GB.	Limit the size of the backup file to less than 5GB.
Another backup is in progress. Backup will not be performed.	Not implemented	The backup failed because of an attempt to back up or merge files while another backup or restore was in progress.	Wait until the backup or restore is complete before starting another backup.
Watchdog Process Monitoring
WATCHDOG: <registered client name> failed on <server IP address>	Critical	The watchdog process detected a registered client failure on a specific server. The <registered client name> could be one of the following: Clusterd _timeout DB_Sentinel Process_Manager Clusterd_monitor Disk_monitor	Review the syslog file to identify the possible cause of this problem.
Microsoft Server
Microsoft server <hostname>/<IP address> has failed.	Major	The Microsoft server could not be reached.	Check that the Microsoft server is connected to the network and configured properly.
Microsoft server <hostname>/<IP address> is OK.	Informational	The Microsoft server can be reached and is functioning properly.	No action is required.
Microsoft DNS/DHCP Service
Service connection to Microsoft DNS server <hostname>/<IP address> has failed.	Major	The Microsoft DNS service is not responding.	Check that the DNS service is configured and running on the Microsoft server.
Service connection to Microsoft DHCP server <hostname>/<IP address> has failed.	Major	The Microsoft DHCP service is not responding.	Check that the DHCP service is configured and running on the Microsoft server.
Service connection to Microsoft DNS server <hostname>/<IP address> is OK.	Informational	The Microsoft DNS service is responding.	No action is required.
Service connection to Microsoft DHCP server <hostname>/<IP address> is OK.	Informational	The Microsoft DHCP service is responding.	No action is required.
NAC Authentication Server Group
NAC Authentication server group is down	Major	None of the servers in the NAC authentication server group can be reached.	Review the syslog.
NAC Authentication server group is up	Informational	The NAC authentication server group is responding.	No action is required.
GUI Login
A GUI login failure has occurred	Major	An admin failed to log in to the GUI.	Check the credentials of the admin.
Serial Console Login
A Serial Console login failure has occurred	Major	An admin failed to log in through the serial console.	Check the credentials and permissions, and check that the serial console is enabled.
Reboot
The system is rebooting.	Informational	A system reboot command was sent.	No action is required.
DHCP Lease Conflict
DHCP address conflicts with an existing lease.	Major	The discovery process found a DHCP lease conflict.	In the IP Map or List panel, select a conflicting address, and then click Resolve Conflict. For more information about resolving DHCP lease conflicts, see Managing Discovered Data.
DHCP Fixed Address Conflict
DHCP address conflicts with an existing fixed address.	Major	The discovery process found a fixed address conflict.	In the IP Map or List panel, select a conflicting address, and then click Resolve Conflict. For more information about resolving fixed address conflicts, see Managing Discovered Data.
DHCP Range Conflict
DHCP address conflicts with an existing range.	Major	The discovery process found a conflict with an existing range.	In the IP Map or List panel, select a conflicting address, and then click Resolve Conflict. For more information about resolving DHCP range conflicts, see Managing Discovered Data.
DHCP Host Conflict
DHCP address conflicts with an existing host address.	Major	The discovery process found a conflict with an existing host address.	In the IP Map or List panel, select a conflicting address, and then click Resolve Conflict. For more information about resolving host conflicts, see Managing Discovered Data.
DNS Health Check Monitor
DNS Health Check query failed.	Major	DNS Health Check query has failed.	Review the syslog file to identify the possible cause of this problem.
DNS Health Check query has succeeded	Informational	DNS Health Check query has succeeded.	No action required.
Syslog Daemon Failure
Syslog daemon is not running.	Critical	Syslog process stopped.	Review the syslog file to identify the possible cause of this problem.
BFD Daemon Failure
An BFD daemon failure has occurred.	Major	BFD has failed to detect failure in the bidirectional path between two interfaces.	Review the syslog file to identify the possible cause of this problem.
Process Stop/Start
The system stopped and started a process.	Major	The system restarted a process.	Review the syslog file to identify the possible cause of this problem.
Zone Transfer Failed
A zone transfer failure has occurred.	Major	A zone transfer failed.	Review the syslog file to identify the possible cause of this problem.
RPZ Refresh Failed
RPZ refresh failure has occurred.	Critical	An RPZ refresh has failed. The appliance sends this trap only when RPZ refresh from all the configured primary servers fail.	Review the syslog file to identify the possible cause of this problem.
Unbound Software Failed
A unbound daemon monitoring failure has occurred.	Major	Unbound software failure has occurred.	Review the syslog file to identify the possible cause of this problem.
Threat Analytics Service Failed
Threat Analytics Auto Download has failed.	Major	Auto download for Threat Analytics has failed.	Review the syslog file to identify the possible cause of this problem.
Outbound Service Failed
The Outbound worker failed.	Major	The Outbound service failure has occurred.	Review the syslog file to identify the possible cause of this problem.
Clear
SNMP Trap is cleared. LCD failure	N/A	The SNMP Trap for LCD failure is cleared.	No action is required.
SNMP Trap is cleared. Serial Console	N/A	The SNMP Trap for Serial Console is cleared.	No action is required.
SNMP Trap is cleared. ControlD failure	N/A	The SNMP Trap for ControlD failure is cleared.	No action is required.
SNMP Trap is cleared. GUI Login	N/A	The SNMP Trap for GUI Login is cleared.	No action is required.
SNMP Trap is cleared. Serial Console Login	N/A	The SNMP Trap for Serial Console Login is cleared.	No action is required.
SNMP Trap is cleared. SSHD failure	N/A	The SNMP Trap for SSHD failure is cleared.	No action is required.
SNMP Trap is cleared. LDAP servers	N/A	The SNMP Trap for LDAP server is cleared.	No action is required.
SNMP Trap is cleared. OCSP Responders	N/A	The SNMP Trap for OCSP Responders is cleared.	No action is required.
SNMP Trap is cleared. OSPF	N/A	The SNMP Trap for OSPF is cleared.	No action is required.
SNMP Trap is cleared. OSPF6	N/A	The SNMP Trap for OSPF6 is cleared.	No action is required.
SNMP Trap is cleared. BGP	N/A	The SNMP Trap for BGP is cleared.	No action is required.
SNMP Trap is cleared. HSM	N/A	The SNMP Trap for HSM is cleared.	No action is required.
SNMP Trap is cleared. HTTP	N/A	The SNMP Trap for HTTP is cleared.	No action is required.
SNMP Trap is cleared. Cluster	N/A	The SNMP Trap for Cluster is cleared.	No action is required.
SNMP Trap is cleared. DuplicateIP	N/A	The SNMP Trap for Duplicate IP is cleared.	No action is required.
Restart
The system is being restarted.	Informational	A system restart command was sent.	No action is required.
DNS Integrity Check
Cannot perform DNS Integrity Check because the appliance is unable to connect to the external DNS server. There are list of nameservers failure: <IP addresses>	N/A	The DNS integrity check cannot be performed because the appliance is unable to connect to the external DNS server.	No action is required.

Threshold Crossing Traps

ibTrapDesc OID 3.1.1.1.2.11.0	ibTrapSeverity	ibObjectName OID 3.1.1.1.2.3.0	Description/Cause	Recommended Actions
System Memory Usage
System has run out of memory.	Major	memory	The appliance ran out of memory. The appliance encountered this problem when one of the following occurred: The total free memory on the appliance was less than or equal to 0%. The total physical memory was less than the total free memory. The percentage of free memory compared to the total physical memory was less than 5%, and the free swap percentage was less than 80%. The percentage of free memory compared to the total physical memory was less than 5%, plus the numbers of both swap INs and swap OUTs were greater than or equal to 3,200. The percentage of free memory compared to the total physical memory was between 5% and 10%, the free swap percentage was greater than or equal to 80%, plus the numbers of both swap INs and swap OUTs were greater than or equal to 3,200. The percentage of free memory compared to the total physical memory was greater than 10%, the free swap percentage was less than 80%, plus the numbers of both swap INs and swap OUTs were greater than or equal to 3,200. Note: Free memory = free physical RAM + free cache buffers. The high threshold for swap pages is 3,200.
System memory usage exceeds the critical threshold value.	Minor	memory	The memory usage on the appliance exceeded the configured Trigger value. For more information about defining thresholds for traps, see Configuring SNMP. The appliance encountered this problem when one of the following occurred: The percentage of free memory compared to the total physical memory was less than 5%, and the free swap percentage was less than 90%. The percentage of free memory compared to the total physical memory was less than 5%, plus the number of swap INs was less than 3,200 and the number of swap OUTs was greater than or equal to 3,200. The percentage of free memory compared to the total physical memory was between 5% and 10%, and the free swap percentage was less than 80%. The percentage of free memory compared to the total physical memory was greater than 5%, plus the number of swap INs was less than 3,200 and the number of swap OUTs was greater than or equal to 3,200. Note: Free memory = free physical RAM + free cache buffers. The high threshold for swap pages is 3,200.
System memory usage is OK.	Minor	memory	The memory usage on the system is at or below the Reset value after it went above the Trigger value.
Primary Hard Drive Usage (monitored every 30 seconds)
System primary hard disk usage is over threshold value.	Minor	disk_usage	The appliance sends this trap when primary hard disk usage first exceeds the configured Trigger value. The default value is 85. The alert light is yellow. For more information about defining thresholds for traps, see Configuring SNMP.	Review the syslog file to identify the possible cause of this problem.
Primary drive is full.	Major	disk_usage	The primary hard disk usage exceeded 95%. The alert light is red.	Review the syslog file to identify the possible cause of this problem.
Primary drive usage is OK.	Minor	disk_usage	The appliance sends this trap when the primary hard disk usage first moves at or below the configured Reset value after it exceeded the Trigger value. The default is 70. The alert light is green.	No action is required.
CPU Usage
CPU usage above threshold value.	Major	cpu_usage	CPU usage exceeded the Trigger value for 15 seconds. For more information about defining thresholds for traps, see Configuring SNMP.	Monitor CPU usage.
CPU usage OK.	Minor	cpu_usage	CPU usage dipped below the reset value after the "CPU usage above threshold value" trap was sent.	No action is required.
Note: Use the CLI command set thresholdtrap to enable the CPU usage trap and configure the trigger and reset values. For information, refer to the Infoblox CLI Guide.
Swap Usage .1.3.6.1.4.1.7779.3.1.1.2.1.2.8.
System swap space usage exceeds the critical threshold value.	Major	swap_usage	System swap space usage exceeded the Trigger value. For more information about defining thresholds for traps, see Configuring SNMP.	Monitor System swap usage.
System swap space usage is OK.	Minor	swap_usage	System swap space usage dipped below the reset value after it exceeded the Trigger value.	No action is required.
Replication Statistics Monitoring
Grid queue replication problem.	N/A	For send trap: Cluster_Send_ Queue For receive trap: Cluster_Recv_ Queue	The system encountered this problem when all of the following conditions occurred: The node was online. The number of the replication queue being sent from the master column was greater than 0, or the number of the queue received was greater than 0. It was more than 10 minutes since the last replication queue was sent and monitored.	Review the syslog file to identify the possible cause of this problem.
DHCP Range Threshold Crossing
DHCP high threshold crossed: Member: <DHCP server node VIP> Network: <network>/ <network view> Range: <DHCP range>/ <network view> High Trigger Mark: <high percentage> (95% by default) High Reset Mark: <reset percentage> (80% by default) Current Usage: <current usage percentage> Active Leases: <number of active leases> Available Leases: <number of available leases> Total Addresses: <total addresses>	N/A	Threshold	The system encountered this problem when the address usage in the DHCP range is greater than the configured High Trigger value.	Review the syslog file to identify the possible cause of this problem.
DHCP high threshold reset: Member: <DHCP server node VIP> Network: <network>/ <network view> Range: <DHCP range>/<network view> High Trigger Mark: <high percentage> (95% by default) High Reset Mark: <reset percentage> (80% by default) Current Usage: <current usage percentage> Active Leases: <number of active leases> Available Leases: <number of available leases> Total Addresses: <total addresses>	N/A	Threshold	The system encountered this problem when the address usage in the DHCP range goes below the Reset value after it hit the Trigger value.
IPAM Utilization Threshold Crossing
Network IPAM Utilization capacity usage is over the threshold value. Network: <network>/ <network view>	N/A	Threshold	The appliance sends this trap when the IPAM utilization for a network is above the configured Trigger value.	Review the syslog file to identify the possible cause of this problem.
Network Container IPAM Utilization capacity usage is over the threshold value. Network container: <network>/ <network view>	N/A	Threshold	The appliance sends this trap when the IPAM utilization for a network container is above the configured Trigger value.	Review the syslog file to identify the possible cause of this problem.
Network IPAM Utilization capacity usage is OK. Network: <network>/ <network view>	N/A	Threshold	The appliance sends this trap when the IPAM utilization for a network is below the configured Reset value.	Review the syslog file to identify the possible cause of this problem.
Network Container IPAM Utilization capacity usage is OK. Network container: <network>/ <network view>	N/A	Threshold	The appliance sends this trap when the IPAM utilization for a network container is below the configured Reset value.	Review the syslog file to identify the possible cause of this problem.
DHCP DDNS Updates Deferred
DHCP DNS updates deferred: Retried at least once: <number of retries> Maximum number of deferred updates since start of problem episode (or restart): <max number>	N/A	Threshold	The DNS updates were deferred because of DDNS update errors.	Review the syslog file to identify the possible cause of this problem.
RPZ Hit Rate
RPZ hit rate exceed normal value.	N/A	Threshold	The appliance sends this trap when the RPZ hit rate exceeds the configured Trigger value.	Review the syslog file to identify the possible cause of this problem.
RPZ hit rate has returned to normal value.	N/A	Threshold	The appliance sends this trap when the RPZ hit rate equals the configured Reset value.	Review the syslog file to identify the possible cause of this problem.
Threat Protection Total Traffic
Threat Protection Service total traffic is above threshold.	N/A	Threshold	The appliance sends this trap when the Treat Protection total traffic exceeds the configured Trigger value.	Review the syslog file to identify the possible cause of this problem.
Threat Protection Service total traffic is OK.	N/A	Threshold	The appliance sends this trap when the Threat Protection total traffic is less than the configured Reset value.	Review the syslog file to identify the possible cause of this problem.
Threat Protection Dropped Traffic
Threat Protection Service dropped traffic is above threshold.	N/A	Threshold	The appliance sends this trap when the Treat Protection dropped traffic exceeds the configured Trigger value.	Review the syslog file to identify the possible cause of this problem.
Threat Protection Service dropped traffic is OK.	N/A	Threshold	The appliance sends this trap when the Threat Protection dropped traffic is less than the configured Reset value.	Review the syslog file to identify the possible cause of this problem.
Database Capacity Usage
Database capacity used is over the threshold value.	Minor	db_usage	The appliance database usage exceeded the configured threshold value.	Increase the database capacity.
Database capacity used is OK.	Minor	db_usage	The appliance database usage is less than the configured threshold value.	No action is required.
DNS Monitor
DNS security alert. There were actual DNS responses to invalid ports in the last minute, comprising percent% of all responses. Primary sources: ip_address sent count, ip_address sent count.	Major	dns_security_ port	DNS security alert. There were actual DNS responses to invalid ports in the last minute, comprising percent% of all responses. Primary sources: ip_address sent count, ip_address sent count. where actual is the total number of DNS responses arrive on invalid ports. percent% is the percentage of invalid DNS responses over the total number of DNS responses. ip_address is the IP address of the primary source that generated the invalid DNS responses. count is the number of invalid responses generated by the specified IP address. Example: DNS security alert. There were 1072 DNS responses to invalid ports in the last minute, comprising 92% of all responses. Primary sources: 10.0.0.0 sent 1058, 2.2.2.2 sent 14.	Review the following: DNS alert status syslog file Limit access or block connections from the primary sources. For information about configuring rate limiting rules, see Monitoring Tools.
DNS security alert. There were actual DNS responses with invalid TXID in the last minute, comprising percent% of all responses. Primary sources: ip_address sent count, ip_address sent count.	N/A	dns_security_t xid	DNS security alert. There were actual DNS responses with invalid TXID in the last minute, comprising percent% of all responses. Primary sources: ip_address sent count, ip_address sent count. where actual is the total number of DNS responses that have invalid TXIDs. percent% is the percentage of invalid DNS responses over the total number of DNS responses. ip_address is the IP address of the primary source that generated the invalid DNS responses. count is the number of invalid responses generated by the specified IP address. Example: DNS security alert. There were 1072 DNS responses with invalid TXID in the last minute, comprising 92% of all responses. Primary sources: 10.0.0.0 sent 1058, 2.2.2.2 sent 14.	Review the following: DNS alert status syslog file Limit access or block connections from the primary sources. For information about configuring rate limiting rules, see Monitoring Tools.
Number of simultaneous DNS lookups exceeds the critical threshold value.	Major	Recursive Clients	The BIND recursive-clients quota defines the maximum number of simultaneous recursive lookups the server will perform on behalf of clients. The appliance sends a trap when the recursive client usage exceeds the specified Trigger percentage of the recursive client quota level. After a trap is sent, no further traps are sent until the number of simultaneous recursive lookups drops below the specified Reset percentage of the recursive client quota level. For more information about configuring the threshold, see Defining Thresholds for Traps.	Check the BIND CHR and the incoming query rate.
Number of simultaneous DNS lookups is OK.	Minor	Recursive Clients	Recursive client usage dipped below the reset value.	No action is required.
RootFS Partition Monitor
Root file system is full.	Major	Root filesystem	The Root filesystem usage exceeded the maximum.	Review the syslog file to identify the possible cause of this problem.
Root file system disk usage is over threshold value.	Minor	Root filesystem	The appliance sends this trap when the Root filesystem usage first exceeds the configured Trigger value.	Review the syslog file to identify the possible cause of this problem.
Root file system disk usage is OK.	Minor	Root filesystem	The appliance sends this trap when the Root filesystem disk usage first moves at or below the configured Reset value after it exceeded the Trigger value. For more information about defining thresholds for traps, see Configuring SNMP.	No action
Reporting
Reporting drive is full.	Major	reporting_service	Reporting drive reached the maximum capacity.	Review the syslog file to identify the possible cause of this problem.
Reporting drive usage is over threshold value.	Minor	reporting_service	The appliance sends this trap when the Reporting volume first exceeds the configured Trigger value. The default Trigger value is 80.	Review the syslog file to identify the possible cause of this problem.
Reporting drive usage is OK.	Minor	reporting_service	The appliance sends this trap when the Reporting volume first moves at or below the configured Reset value after it exceeded the Trigger value. The default Reset value is 71. For information on setting the Trigger and Reset values, see Configuring SNMP.	No action
File Distribution
File Distribution services storage usage reached the threshold value.	N/A	File Distribution	File distribution service storage reached the configured threshold value.	Review the syslog file to identify the possible cause of this problem.

Object State Change Traps

ibTrapDesc OID 3.1.1.1.2.11.0	ibTrapSeverity	Description/Cause	Recommended Actions
Service Shutdown
Shutting down services due to database snapshot.	Major	The appliance is shutting down its services while synchronizing the database with the Grid Master.	No action is required.
Network Interfaces Monitoring
LAN1 port link is down. Please check the connection.	Major	The LAN1 port is up, but the link is down.	Check the LAN1 link connection.
LAN2 port link is down. Please check the connection.	Major	The LAN2 port is up, but the link is down.	Check the LAN2 link connection.
HA port link is down. Please check the connection.	Major	The HA port is up, but the link is down.	Check the HA link connection.
MGMT port link is down. Please check the connection.	Major	The MGMT port is enabled, but the link is down.	Check the MGMT link connection.
LAN1 port link is up.	Major	The LAN1 port link is up and running.	No action is required.
LAN2 port link is up.	Major	The LAN2 port link is up and running.	No action is required.
HA port link is up.	Major	The HA port link is up and running.	No action is required.
MGMT port link is up.	Major	The MGMT port link is up and running.	No action is required.
HA State Change from Initial to Active
The node has become ACTIVE.	Informational	A node in an HA pair becomes active. The HA pair starts up.	No action is required.
HA State Change from Passive to Active
The node has become ACTIVE.	Informational	The node changed from a passive to an active node.	No action is required.
HA State Change to Active-Active
The node is in an ACTIVE-ACTIVE state.	Informational	The node is in the active state.	No action is required.
HA State Change from Initial to Passive
The node has become PASSIVE.	Informational	A node in an HA pair becomes passive. The HA pair starts up, and the node is not a Grid Master candidate.	No action is required.
Node Connected to Grid
The Grid member is connected to the Grid master.	Informational	The Grid member joined the Grid, and it is not a Grid Master candidate.	No action is required.
Node Disconnected from Grid
The Grid member is not connected to the Grid master.	Informational	The Grid member lost its connection to the Grid Master.	No action is required.
Replication State Monitoring
HA replication is online.	Informational	The HA replication is online.	No action is required.
HA replication is offline.	Informational	The HA replication is offline.	No action is required.
NTP is out of sync, monitored every 30 seconds
The NTP service is out of synchronization.	Major	The Infoblox NTP server and the external NTP server are not synchronized.	Review the syslog file to identify the possible cause of this problem.
NTP Service is working.	Informational	The NTP service started working again.	No action is required.
NTP service is synchronizing to local clock
The NTP service is synchronizing to local clock.	Major	The Infoblox NTP server synchronizes its clients with its local clock.	No action is required.
DHCP service state change
DHCP Service is working.	Informational	The DHCP service started working again.	No action is required.
DHCP Service is in a warning state.	Informational	The DHCP service is in a warning state.	Review the syslog file
DHCP Service Failed	Informational	The DHCP service is in failed state.	Review the syslog file.
DHCP Service is inactive.	Informational	The DHCP service became inactive.	Check if an admin disabled the service.
DNS service state change
DNS Service is working.	Informational	The DNS service started working again.	No action is required.
DNS Service failed	Informational	The DNS service is in a failed state.	Review the syslog file.
DNS Service is inactive.	Informational	The DNS service became inactive.	Check if an admin disabled the service.
NTP service state change
The NTP service resumed synchronization.	Informational	The NTP service started working again.	No action is required.
NTP Service is inactive.	Informational	The NTP service became inactive.	Check if an admin disabled the service.
TFTP service state change
TFTP Service is working.	Informational	The TFTP service started working again.	No action is required.
TFTP Service is inactive.	Informational	The TFTP service became inactive.	Check if an admin disabled the service.
FTP service state change
FTP Service is working.	Informational	The FTP service started working again.	No action is required.
FTP Service is inactive.	Informational	The FTP service became inactive.	Check if an admin disabled the service.
HTTP service state change
HTTP File Dist Service is working.	Informational	The HTTP file distribution service started working again.	No action is required.
HTTP File Dist Service is inactive.	Informational	The HTTP file distribution service became inactive.	Check if an admin disabled the service.
bloxTools service state change
BloxTools Service is working.	Informational	The bloxTools service started working again.	No action is required.
BloxTools Service is in warning state.	Informational	The bloxTools service is in a warning state.	Review the syslog file
BloxTools Service is inactive.	Informational	The bloxTools service became inactive.	Check if an admin disabled the service.
BloxTools Service failed.	Critical	The bloxTools daemon failed.	Review the syslog file.
Captive Portal service state change
Captive Portal Service is working.	Informational	The captive portal service started working again.	No action is required.
Captive Portal Service is inactive.	Informational	The captive portal service became inactive.	Check if an admin disabled the service.
Discovery Collector service state change
Discovery Collector Service is working.	Informational	The discovery collector service started working again.	No action is required.
Discovery Collector Service is inactive.	Informational	The discovery collector service became inactive.	Check if an admin disabled the service.
Discovery Collector Service is in warning state.	Informational	The discovery collector service is in a warning state.	Review the syslog file.
Discovery Collector Service has failed.	Informational	The discovery collector service has failed.	Review the syslog file.
Discovery Collector service state change
Discovery Consolidator Service is working.	Informational	The discovery consolidator service started working again.	No action is required.
Discovery Consolidator Service is inactive.	Informational	The discovery consolidator service became inactive.	Check if an admin disabled the service.
Discovery Consolidator Service is in warning state.	Informational	The discovery consolidator service is in a warning state.	Review the syslog file
Discovery Consolidator Service has failed.	Critical	The discovery consolidator service has failed.	Review the syslog file
IF-MAP service state change
IFMAP Service is inactive.	Informational	The IF-MAP service became inactive.	Check if an admin disabled the service.
IFMAP Service is working.	Informational	The IF-MAP service started working again.	No action is required.
LDAP service state change
LDAP service is inactive.	Informational	The LDAP service became inactive.	Check if an admin disabled the LDAP service.
All LDAP servers are available.	Informational	All LDAP servers are available.	No action is required.
At least one LDAP server is unavailable.	Major	At least one LDAP server is out of service.	Check if an admin disabled the LDAP server. Review the syslog file.
All LDAP servers are unavailable.	Informational	All LDAP servers are not available.	Check if an admin disabled the LDAP server. Review the syslog file.
Certificate Authentication Service state change
CAS service is working.	Informational	The certificate authentication service started working again.	No action is required.
CAS service is inactive.	Informational	The certificate authentication service became inactive.	Check if an admin disabled the service.
OCSP responders state change
All OCSP responders available.	Informational	The OCSP responders are available.	No action is required.
All OCSP responders are out of service.	Informational	The OCSP responders are out of service.	Check if an admin disabled the service. Review the syslog file.
OCSP service inactive.	Informational	The OCSP responders service became inactive.	Check if an admin disabled the service. Review the syslog file.
Reporting service state change
Reporting Service is working.	Informational	The Reporting service started working again.	No action is required.
Reporting Service failed.	Informational	The Reporting Service is in Failed state.	Review the syslog file.
Reporting Service is inactive.	Informational	The Reporting service became inactive.	Check if an admin disabled the service.
Reporting Service is in warning state.	Informational	The Reporting service is in warning state.	Review the audit log file.
Threat Analytics state change
Threat Analytics Service is working.	Informational	The Threat Analytics service started working again.	No action is required.
Threat Analytics Service is inactive.	Informational	The Threat Analytics service became inactive.	Check if an admin disabled the service.
Threat Analytics Service is failed.	Informational	The Threat Analytics service has failed.	Review the audit log file.
Threat Analytics Service is in warning state.	Informational	The Threat Analytics service is in warning state.	Review the audit log file.
RPZ refresh state change
RPZ refresh is OK.	Informational	An RPZ refresh succeeded. The appliance sends this trap every time an RPZ zone transfer is successful.	No action is required.
Cisco ISE service state change
Cisco ISE server is OK.	Informational	The Cisco ISE service started working again.	No action is required.
Connection Error has occurred In Cisco ISE server.	Informational	There is a loss of connection between the NIOS appliance and Cisco ISE server.	Check if an admin disabled the service. Review the audit log file.
Cloud API service state change
Cloud API service is working.	Informational	The Cloud API service started working again.	No action is required.
Cloud API service is inactive.	Informational	The Cloud API service became inactive	Check if an admin disabled the Cloud API service. Review the audit log file.
Cloud API service has failed.	Critical	The Cloud API service has failed.	Check if an admin disabled the Cloud API service. Review the audit log file.
DNS Integrity Check state change
DNS Integrity Check is working.	Informational	The DNS Integrity Check started working again.	No action is required.
DNS Integrity Check failed.	Informational	The DNS Integrity Check has failed.	Check if an admin disabled the service. Review the audit log file.
DNS Integrity Check severity has changed.	Informational	The DNS Integrity Check has changed.	Review the syslog file.
TAXII service state change
TAXII service is working.	Informational	The TAXII service started working again.	No action is required.
TAXII Service is failed.	Informational	The TAXII service has failed.	Check if an admin disabled the service. Review the audit log file.
TAXII service is inactive.	Informational	The TAXII service became inactive.	Check if an admin disabled the service. Review the audit log file.
TAXII Service is in warning state.	Informational	The TAXII service is in warning state.	Review the audit log file.
Outbound service state change
The Outbound Service Manager stopped.	Informational	The Outbound service manager has stopped working.	Check if an admin disabled the service. Review the audit log file.
The Outbound Service Manager failed.	Major	The Outbound service manager has failed.	Check if an admin disabled the service. Review the audit log file.
The Outbound Service Manager started.	Informational	The Outbound service manager has started.	No action is required.
The Outbound worker failed.	Major	The Outbound worker has failed.	Review the audit log file.
IPMI Device state change
IPMI is used by some hardware monitors to test hardware health. The IPMI Device has not responded. Hardware monitors may show spurious failures.	Informational	The IPMI Device has not responded.	Check if an admin disabled the IPMI interface. Review the audit log file.
IPMI is used by some hardware monitors to test hardware health. Because the IPMI Device has not responded for a while, hardware monitor failures are likely to be spurious.	Informational	The IPMI Device has not responded.	Check if an admin disabled the IPMI interface. Review the audit log file.
IPMI is used by some hardware monitors to test hardware health. The IPMI Device is now available; subsequent hardware monitor failures are likely to be genuine.	Informational	The IPMI Device is now available	No action required.

Process Started and Stopped Traps

ibTrapDesc OID 3.1.1.1.2.11.0	ibTrapSeverity	Description/Cause	Recommended Actions
Httpd Start
The process started normally.	Informational	The httpd process started.	No action is required.
Httpd Stop
The process stopped normally.	Informational	The httpd process stopped.	No action is required.
Process Stop/Start
The system stopped and started a process.	Major	The system restarted a process.	No action is required.
Zone Transfer Failed
A zone transfer failure has occurred.	Critical	A zone transfer failed.	Review the syslog file

Revoked License Trap

ibTrapDesc OID 3.1.1.1.2.11.0	ibTrapSeverity	Description/Cause	Recommended Actions
Revoked License
This trap is generated when a license is revoked	Critical	A license was revoked.	Obtain and install new license

ibPlatformOne MIB

The ibPlatformOne MIB provides information about the CPU temperature of the appliance, the replication status, the average latency of DNS requests, DNS security alerts, CPU and memory utilization of the appliance, and the Infoblox service status. The figure below illustrates the structure of the PlatformOne MIB. (Note that the OIDs in the illustration do not include the prefix .1.3.6.1.4.1.7779.)
The ibPlatformOne MIB contains the following objects:

ibCPUTemperature (IbString) tracks the CPU temperature of the appliance.
ibClusterReplicationStatusTable provides information in tabular format about the replication status of the appliance.
ibNetworkMonitor provides information about the average latency of authoritative and nonauthoritative replies to DNS queries for different time intervals. It also provides information about invalid DNS responses that arrive on invalid ports or have invalid DNS transaction IDs.
ibHardwareType (IbString) provides information about the hardware platform. For an Infoblox appliance, it provides the model number of the Infoblox hardware platform. For vNIOS appliances, it identifies if the hardware platform is VMware.
ibHardwareId (IbString) provides the hardware ID of the NIOS appliance.
ibSerialNumber (IbString) provides the serial number of the Infoblox hardware platform.
ibNiosVersion (IbString) provides the version of the NIOS software.
ibSystemMonitor provides information about the CPU and memory utilization of the appliance.
ibGridStatus provides information about an appliance. It indicates whether the appliance is a Grid Master, member, or an independent appliance.
ibHAStatus provides information about the HA status of a member. It indicates if the member is part of an HA configuration, and if it is the active or passive node.
ibGridMasterCandStatus indicates if a member is a Grid Master candidate.
ibGridMasterVIP provides the Grid Master virtual IP address.
ibGridReplicationState provides information about the replication status.

The ibPlatformOne MIB also contains the following tables that provide status of the Infoblox services as well as system and hardware services on the appliance you query:

ibMemberServiceStatusTable provides status of the Infoblox services, such as the DNS and DHCP services, on a queried appliance.
ibMemberNodeServiceStatusTable provides status of the system and hardware services on a queried appliance.
ibMemberPassiveNodeServiceStatusTable provides status of the system and hardware services on the passive node of an HA pair if the queried appliance is the VIP or the active node of an HA pair. For independent appliances and the passive nodes of HA pairs, this table does not display any status.

ibPlatformOne MIB Structure

ibClusterReplicationStatusTable

ibClusterRepliactionStatusTable (object ID 3.1.1.2.1.2.1) provides information about the Grid replication status. The following figure shows the sub branches of ibClusterReplicationStatusTable:

ibClusterReplicationStatusTable Objects

The following table provides information about the ibClusterReplicationStatusTable objects:

ibClusterReplicationStatusTableObjects

Object (Type)	Description
ibClusterReplicationStatusEntry	A conceptual row that provides information about the Grid replication status. The status indicates whether the appliance is sending replication queues, receiving queues, or having problems with the replication.
ibNodeIPAddress (IbIpAddr)	IP address of a Grid member.
ibNodeReplicationStatus (IbString)	Replication status of the Grid member. The replication status can be one of the following: online, offline, or snapshotting.
ibNodeQueueFromMaster (Integer)	“Sent” queue size from master.
ibNodeLastRepTimeFromMaster (IbString)	Last sent time from master.
ibNodeQueueToMaster (Integer)	“Receive” queue size from master.
ibNodeLastRepTimeToMaster (IbString)	Last receive time from master.

ibNetwork Monitor

As shown in the following ibNetWorkMonitorObjects figure, the ibNetwork Monitor has one subtree, ibNetworkMonitorDNS, that branches out into the following:

ibNetworkMonitorDNSActive (Integer) reports on whether DNS latency monitoring is enabled. You can enable DNS latency monitoring using the CLI command set monitor dns. For more information about enabling and disabling DNS alert monitoring, see Monitoring Tools. This is the only object in this branch. When you send a query for this object, the appliance responds with either "active" (1) or "nonactive" (0).
ibNetworkMonitorDNSNonAA provides information about the average latency of nonauthoritative replies to DNS queries for 1-, 5-, 15-, and 60-minute intervals.
ibNetworkMonitorDNSAA provides information about the average latency of authoritative replies to DNS queries for 1-, 5-, 15-, and 60-minute intervals.
ibNetworkMonitorDNSSecurity provides information about the invalid DNS responses that arrive on invalid ports or have invalid DNS transaction IDs. ibNetworkMonitorDNSSecurity branches out into the following:
- ibNetworkMonitorDNSSecurityInvalidPort
- ibNetworkMonitorDNSSecurityInvalidTxid
- ibNetworkMonitorDNSSecurityInvalidPortOnly (Counter)
- ibNetworkMonitorDNSSecurityInvalidPortCount (Counter)
- ibNetworkMonitorDNSSecurityInvalidTxidOnly (Counter)
- ibNetworkMonitorDNSSecurityInvalidTxidCount (Counter)
- ibNetworkMonitorDNSSecurityInvalidTxidAndPort (Counter)

ibNetWorkMonitorObjects

ibNetworkMonitorDNSNonAAandibNetworkMonitorDNSAASubtrees

The table below describes the objects in ibNetworkMonitorDNSNonAA. You can send queries to retrieve values for these objects.

ibNetworkMonitorDNSNonAA Objects

Object (Type)	Description
ibNetworkMonitorDNSNonAAT1	File that contains the objects for monitoring the average latency of nonauthoritative replies to queries in the last minute.
ibNetworkMonitorDNSNonAAT1AvgLatency (Integer)	Indicates the average latency in microseconds of nonauthoritative replies to queries in the last minute.
ibNetworkMonitorDNSNonAAT1Count (Integer)	Indicates the number of queries used to calculate the average latency of nonauthoritative replies in the last minute.
ibNetworkMonitorDNSNonAAT5	File that contains the objects for monitoring the average latency of nonauthoritative replies to queries in the last five minutes.
ibNetworkMonitorDNSNonAAT5AvgLatency (Integer)	Indicates the average latency in microseconds of nonauthoritative replies to queries in the last five minutes.
ibNetworkMonitorDNSNonAAT5Count (Integer)	Indicates the number of queries used to calculate the average latency of nonauthoritative replies in the last five minutes.
ibNetworkMonitorDNSNonAAT15	File that contains the objects for monitoring the average latency of nonauthoritative replies to queries in the last 15 minutes.
ibNetworkMonitorDNSNonAAT15AvgLatency (Integer)	Indicates the average latency in microseconds of nonauthoritative replies to queries in the last 15 minutes.
ibNetworkMonitorDNSNonAAT15Count (Integer)	Indicates the number of queries used to calculate the average latency of nonauthoritative replies in the last 15 minutes.
ibNetworkMonitorDNSNonAAT60	File that contains the objects for monitoring the average latency of nonauthoritative replies to queries in the last 60 minutes.
ibNetworkMonitorDNSNonAAT60AvgLatency (Integer)	Indicates the average latency in microseconds of nonauthoritative replies to queries in the last 60 minutes.
ibNetworkMonitorDNSNonAAT60Count (Integer)	Indicates the number of queries used to calculate the average latency of nonauthoritative replies in the last 60 minutes.
ibNetworkMonitorDNSNonAAT1440	File that contains the objects for monitoring the average latency of nonauthoritative replies to queries in the last 24 hours.
ibNetworkMonitorDNSNonAAT1440AvgLatency (Integer)	Indicates the average latency in microseconds of nonauthoritative replies to queries in the last 24 hours.
ibNetworkMonitorDNSNonAAT1440Count (Integer)	Indicates the number of queries used to calculate the average latency of nonauthoritative replies in the last 24 hours.

The table below describes the objects in ibNetworkMonitorDNSAA. You can send queries to retrieve values for these objects.

ibNetworkMonitorDNSAA Objects

Object (Type)	Description
ibNetworkMonitorDNSAAT1	File that contains the objects for monitoring the average latency of authoritative replies to queries in the last minute.
ibNetworkMonitorDNSAAT1AvgLatency (Integer)	Indicates the average latency in microseconds of authoritative replies to queries in the last minute.
ibNetworkMonitorDNSAAT1Count (Integer)	Indicates the number of queries used to calculate the average latency of authoritative replies in the last minute.
ibNetworkMonitorDNSAAT5	File that contains the objects for monitoring the average latency of authoritative replies to queries in the last five minutes.
ibNetworkMonitorDNSAAT5AvgLatency (Integer)	Indicates the average latency in microseconds of authoritative replies to queries in the last five minutes.
ibNetworkMonitorDNSAAT5Count (Integer)	Indicates the number of queries used to calculate the average latency of authoritative replies in the last five minutes.
ibNetworkMonitorDNSAAT15	File that contains the objects for monitoring the average latency of authoritative replies to queries in the last 15 minutes.
ibNetworkMonitorDNSAAT15AvgLatency (Integer)	Indicates the average latency in microseconds of authoritative replies to queries in the last 15 minutes.
ibNetworkMonitorDNSAAT15Count (Integer)	Indicates the number of queries used to calculate the average latency of authoritative replies in the last 15 minutes.
ibNetworkMonitorDNSAAT60	File that contains the objects for monitoring the average latency of authoritative replies to queries in the last 60 minutes.
ibNetworkMonitorDNSAAT60AvgLatency (Integer)	Indicates the average latency in microseconds of authoritative replies to queries in the last 60 minutes.
ibNetworkMonitorDNSAAT60Count (Integer)	Indicates the number of queries used to calculate the average latency of authoritative replies in the last 60 minutes.
ibNetworkMonitorDNSAAT1440	File that contains the objects for monitoring the average latency of authoritative replies to queries in the last 24 hours.
ibNetworkMonitorDNSAAT1440AvgLatency (Integer)	Indicates the average latency in microseconds of authoritative replies to queries in the last 24 hours.
ibNetworkMonitorDNSAAT1440Count (Integer)	Indicates the number of queries used to calculate the average latency of authoritative replies in the last 24 hours.

The below table describes the objects in ibNetworkMonitorDNSSecurity. When you enable the following, the SNMP traps with these objects are received:

SNMP traps
DNS network monitoring
DNS alert monitoring

ibNetworkMonitorDNSSecurityObjects

Object (Type)	Description
ibNetworkMonitorDNSSecurityInvalidPort	Tracks the number of invalid DNS responses that arrive on invalid ports. For information about invalid ports, monitoring DNS transactions, see Monitoring Tools. This object contains a subtree with six objects that track invalid ports within a certain time interval.
ibNetworkMonitorDNSSecurityInvalidTxid	Tracks the number of invalid TXIDs (DNS transaction IDs). For information about invalid TXIDs, monitoring DNS transactions, see Monitoring Tools. This object contains a subtree with six objects that track invalid TXIDs within a certain time interval.
ibNetworkMonitorDNSSecurityInvalidPortOnly (Counter)	Tracks the number of DNS responses with both of the following conditions: Arrive on invalid ports Have valid TXIDs
ibNetworkMonitorDNSSecurityInvalidTxidOnly (Counter)	Tracks the number of DNS responses with both of the following conditions: Arrive on valid ports Have Invalid TXIDs
ibNetworkMonitorDNSSecurityInvalidPortCount (Counter)	Tracks the total number of invalid DNS responses that arrive on invalid ports.
ibNetworkMonitorDNSSecurityInvalidTxidCount (Counter)	Tracks the total number of DNS responses that have invalid DNS transaction IDs.
ibNetworkMonitorDNSSecurityInvalidTxidAndPort (Counter)	Tracks the number of DNS responses with both of the following conditions: Arrive on invalid ports Have invalid TXIDs

The following table describes the objects in ibNetworkMonitorDNSSecurityInvalidPort:

ibNetworkMonitorDNSSecurityInvalidPort Objects

Object (Type)	Description
ibNetworkMonitorDNSSecurityInvalidPort1 (Integer)	Tracks the number of invalid DNS responses that arrive on invalid ports in the last one minute.
ibNetworkMonitorDNSSecurityInvalidPort5 (Integer)	Tracks the number of invalid DNS responses that arrive on invalid ports in the last five minutes.
ibNetworkMonitorDNSSecurityInvalidPort15 (Integer)	Tracks the number of invalid DNS responses that arrive on invalid ports in the last 15 minutes.
ibNetworkMonitorDNSSecurityInvalidPort60 (Integer)	Tracks the number of invalid DNS responses that arrive on invalid ports in the last 60 minutes.
ibNetworkMonitorDNSSecurityInvalidPort1440 (Integer)	Tracks the number of invalid DNS responses that arrive on invalid ports in the last 24 hours.
ibNetworkMonitorDNSSecurityInvalidPortCount (Counter)	Tracks the total number of invalid DNS responses that arrive on invalid ports.

The following table below describes the objects in ibNetworkMonitorDNSSecurityInvalidTxid:

ibNetworkMonitorDNSSecurityInvalidTxid Objects

Object (Type)	Description
ibNetworkMonitorDNSSecurityInvalidTxid1 (Integer)	Tracks the number of DNS responses that have invalid DNS transaction IDs in the last one minute.
ibNetworkMonitorDNSSecurityInvalidTxid5 (Integer)	Tracks the number of DNS responses that have invalid DNS transaction IDs in the last five minutes.
ibNetworkMonitorDNSSecurityInvalidTxid15 (Integer)	Tracks the number of DNS responses that have invalid DNS transaction IDs in the last 15 minutes.
ibNetworkMonitorDNSSecurityInvalidTxid60 (Integer)	Tracks the number of DNS responses that have invalid DNS transaction IDs in the last 60 minutes.
ibNetworkMonitorDNSSecurityInvalidTxid1440 (Integer)	Tracks the number of DNS responses that have invalid DNS transaction IDs in the last 24 hours.
ibNetworkMonitorDNSSecurityInvalidTxidCount (Counter)	Tracks the total number of DNS responses that have invalid DNS transaction IDs.

ibSystemMonitor

As shown in the figure below, ibSystemMonitor (object ID 3.1.1.2.1.2.8) has the following subtrees:

ibSystemMonitorCpu: Contains ibSystemMonitorCpuUsage (Integer) that reports the CPU usage of the appliance.
ibSystemMonitorMem: Contains ibSystemMonitorMemUsage (Integer) that reports the memory usage of the appliance.
ibSystemMonitorSwap: Contains ibSystemMonitorSwapUsage (integer) that reports the swap usage of the appliance.
ibSystemMonitorSnic: Contains ibSystemMonitorSnicStatsTable1 (integer) and ibSystemMonitorSnicStatsTable5 (integer) that contains the smart NIC (SNIC) details. The OID 3.1.1.2.1.8.4.3.1.1.4.112.111.111.108 indicates that the member is a pool, 3.1.1.2.1.8.4.3.1.1.5.99.97.99.104.101 indicates that the member is a cache, 3.1.1.2.1.8.4.3.1.1.5.116.99.111.114.101 indicates that the cache is tcore, and 3.1.1.2.1.8.4.3.1.1.5.109.99.111.114.101 indicates that the cache is mcore.

ibSystemMonitor Objects3

ibMemberServiceStatusTable

As shown in the figure below, ibMemberServiceStatusTable (object ID 3.1.1.2.1.2.9) has one subtree, ibMemberServiceStatusEntry, which contains the following objects:

ibServiceName (String) reports the names of the Infoblox services.
ibServiceStatus (Integer) reports the status of the Infoblox services.
ibServiceDesc (String) describes the details of the status.

ibMemberServiceStatusTable displays the current status of the Infoblox services on the appliance that you query. For an HA pair, this table displays the service status of the active node. If the appliance you query is the passive node of an HA pair, this table reflects the service status of the passive node, which can be "inactive" or "unknown."
You can also query ibMemberNodeServiceStatusTable and ibMemberPassiveNodeServiceStatusTable that display system and hardware status on the queried appliance.

ibMemberServiceStatusTable Objects

Infoblox Services for ibMemberServiceStatusTable

The following table lists the values and descriptions of the Infoblox services that appear in ibMemberServiceStatusTable:

ibServiceName Values for ibMemberServiceStatusTable

Value	Description	Definition
1	dhcp	DHCP service
2	dns	DNS service
3	ntp	NTP service
4	tftp	File distribution using the TFTP service
5	http-file-dist	File distribution using the HTTP service
6	ftp	File distribution using the FTP service
7	bloxtools-move	Moving the bloxTools service
8	bloxtools	The bloxTools environment

Service Status

When you query the service status on an appliance, the response includes the status of the services. The below table shows the values and descriptions of the status. Note that for internal Grid operations, the NTP service is always in the "working" state even if it has been disabled through the Infoblox GUI.

ibServiceStates Values

Value	Description	Definition
1	working	The service is functioning properly.
2	warning	The service is having some issues. Check the service or hardware function and the syslog to identify the problem.
3	failed	The service failed. Review the syslog to identify the problem.
4	inactive	The service is disabled or out of service.
5	unknown	The appliance cannot detect the current stusof the service.

ibMemberNodeServiceStatusTable

As shown in the below figure, ibMemberNodeServiceStatusTable (object ID 3.1.1.2.1.10) has one subtree, ibMemberNodeServiceStatusEntry, which contains the following objects:

ibMemberNodeServiceName (String) reports the names of the system and hardware services.
ibMemberNodeServiceStatus (Integer) reports the status of the services.
ibMemberNodeServiceDesc (String) describes the details of the status.

ibMemberNodeServiceStatusTable displays the current status of the system and hardware services on the appliance that you query. For example, when you query an independent appliance, this table shows the information about the independent appliance. When you query the VIP of an HA pair, this table shows the information about the active node. For the active node of the HA pair, you can also query ibMemberPassiveNodeStatusTable to get the status of the passive node.

ibMemberNodeServiceStatusTable Objects

Infoblox Services for ibMemberNodeServiceStatusTable

The following table lists the values and descriptions of the Infoblox services that appear in ibMemberNodeServiceStatusTable:

ibServiceName Values for ibMemberNodeServiceStatusTable

Value	Description	Definition
9	node-status	Member status
10	disk-usage	Disk usage
11	enet-lan	LAN port
12	enet-lan2	LAN2 port
13	enet-ha	HA port
14	enet-mgmt	MGMT port
15	lcd	LCD
16	memory	Memory
17	replication	Replication service
18	db-object	Database capacity in %
19	raid-summary	RAID array
20	raid-disk1	RAID Disk 1 (For appliances with RAID arrays)
21	raid-disk2	RAID Disk 2 (For appliances with RAID arrays)
22	raid-disk3	RAID Disk 3 (For appliances with RAID arrays)
23	raid-disk4	RAID Disk 4 (For appliances with RAID arrays)
24	raid-disk5	RAID Disk 5 (For appliances with RAID arrays)
25	raid-disk6	RAID Disk 6 (For appliances with RAID arrays)
26	raid-disk7	RAID Disk 7 (For appliances with RAID arrays)
27	raid-disk8	RAID Disk 8 (For appliances with RAID arrays)
28	fan1	Fan 1
29	fan2	Fan 2
30	fan3	Fan 3
31	fan4	Fan 4
32	fan5	Fan 5
33	fan6	Fan 6
34	fan7	Fan 7
35	fan8	Fan 8
36	power-supply1	Power supply 1
37	power-supply2	Power supply 2
38	ntp-sync	NTP synchronization
39	cpu1-temp	CPU temperature
40	cpu2-temp	CPU temperature
41	sys-temp	System temperature
42	raid-battery	RAID battery
43	cpu-usage	CPU usage
44	ospf	OSPF
45	BGP	BGP
46	mgm-service	Multi-Grid management
47	subGrid-conn	Grid in Master Grid
48	network-capacity	Network capacity
49	reporting	Reporting service
50	dns-cache-acceleration	DNS Cache Acceleration services
51	ospf6	OSPF6
57	cloud-api	Cloud API service

ibMemberPassiveNodeServiceStatusTable

As shown in the below figure, ibMemberPassiveNodeServiceStatusTable (object ID 3.1.1.2.1.2.11) has one subtree, ibMemberPassiveNodeServiceStatusEntry, which contains the following objects:

ibMemberPassiveNodeServiceName (String) reports the names of the system and hardware services.
ibMemberPassiveNodeServiceStatus (Integer) reports the status of the services.
ibMemberPassiveNodeServiceDesc (String) describes details of the status.

ibMemberPassiveNodeServiceStatusTable displays the current status of the system and hardware services on the passive node of an HA pair when you query the VIP of the HA pair. For independent appliances and the passive nodes of HA pairs, this table does not display any status.

ibMemberPassiveNodeServiceStatusTable Objects

ibDHCPOne MIB

The ibDHCPOne MIB provides information about address usage within a subnet, DHCP lease statistics, and DHCP packet counts. It includes two modules, ibDHCPModule for IPv4 data and ibDHCPv6Module for IPv6 data.

ibDHCPModule

The below figure illustrates the structure of the ibDHCPModule. (Note that the OIDs shown in the illustration do not include the prefix .1.3.6.1.4.1.7779.) ibDHCPModule contains the following objects:

ibDHCPSubnetTable provides statistical data about the DHCP operations of the appliance.
ibDHCPStatistics maintains counters for different types of packets.
ibDHCPDeferredQueuesize tracks the total number of deferred DDNS updates that are currently in the queue to be retried. When DDNS updates are deferred due to timeout or server issues, the DHCP server puts these updates in this queue.
ibDHCPDDNSStats monitors the average latency for the DDNS updates in microseconds and the number of timeouts during different time intervals.

ibDHCPModule

ibDHCPSubnetTable provides statistical data about the DHCP operations of the appliance. It contains the following objects:

ibDHCPSubnetTable

Object (Type)	Description
ibDHCPSubnet Entry	File that contains the objects for monitoring DHCP operations on the appliance.
ibDHCPSubnetNetworkAddress (IbIpAddr)	The subnetworks, in IP address format, that have IP addresses for lease. A subnetwork may have many address ranges for lease.
ibDHCPSubnetNetworkMask (IbIpAddr)	The subnet mask in dotted decimal format.
ibDHCPSubnetPercentUsed (Integer)	The percentage of dynamic DHCP addresses leased out at this time for each subnet. The percentage of dynamic DHCP addresses that are leased out are calculated as the [Total number of active leases in the range + Fixed addresses (leased or unused) + DHCP reservation addresses + Host addresses with DHCP enabled inside the specified subnet]/[Total number of IP address available in the range + Number of Fixed address inside the subnet + Number of IPv4 reservation addresses + Host addresses] For example: Network: 10.192.16.0/24 Range: 10.192.16.10 – 10.192.16.20 (11 free IP addresses) Fixed addresses: 10.192.16.3 (outside DHCP range) and 10.192.16.11 (within DHCP range) There are 10 free IP addresses in the DHCP Range: 10.192.16.10 – 10.192.16.20 and one fixed address within the DHCP range IPv4 DHCP Utilization in Infoblox GUI: 16.6% (2/12) -> For this case, (1 fixed address outside range + 1 fixed address within range) / (fixed address outside DHCP range + number of IP addresses in the DHCP range which includes the fixed address within range)] * 100 = (2/12)*100 -> 17% SNMP output from the CLI of the server: Infoblox > show snmp variable .1.3.6.1.4.1.7779.3.1.1.4.1.1.1.3.11.49.48.46.49.57.50.46.49.54.46.48 IB-DHCPONE-MIB::ibDHCPSubnetPercentUsed."10.192.16.0" = INTEGER: 17

Following is an example of the table as viewed through a MIB browser:

MIBBrowserView1

ibDHCPStatistics

ibDHCPStatistics maintains counters for different types of packets. The counters always start with zero when the DHCP service is restarted. Therefore, the numbers reflect the total number of packets received since the DHCP service was last restarted on the appliance. The ibDHCPStatistics module contains the following objects:

ibDHCPStatistics

Object (Type)	Description
ibDhcpTotalNoOfDiscovers (Counter)	The number of DHCPDISCOVER messages that the appliance received. Clients broadcast DHCPDISCOVER messages when they need an IP address and network configuration information.
ibDhcpTotalNoOfRequests (Counter)	The number of DHCPREQUEST messages that the appliance received. A client sends a DHCPREQUEST message requesting configuration information, after it receives the DHCPOFFER message.
ibDhcpTotalNoOfReleases (Counter)	The number of DHCPRELEASE messages that the appliance received from its clients. A client sends a DHCP release when it terminates its lease on an IP address.
ibDhcpTotalNoOfOffers (Counter)	The number of DHCPOFFER messages that the appliance has sent to clients. The appliance sends a DHCPOFFER message to a client. It contains an IP address and configuration information.
ibDhcpTotalNoOfAcks (Counter)	The number of DHCPACK messages that the appliance sent to clients. It sends a DHCPACK message to a client to confirm that the IP address offered is still available.
ibDhcpTotalNoOfNacks (Counter)	The number of DHCPNACK messages that the appliance sent to clients. It sends a DHCPNACK message to withdraw its offer of an IP address.
ibDhcpTotalNoOfDeclines (Counter)	The number of DHCPDECLINE messages that the appliance received. A client sends a DHCPDECLINE message if it determines that an offered IP address is already in use.
ibDhcpTotalNoOfInforms (Counter)	The number of DHCPINFORM messages that the appliance received. A client sends a DHCPINFORM message when it has an IP address but needs information about the network.
ibDhcpTotalNoOfOthers (Counter)	The total number of DHCP messages other than those used in negotiation, such as DHCPFORCERENEW, DHCPKNOWN, and DHCPLEASEQUERY.

ibDHCPDDNSStats

ibDHCPDDNSStats monitors the average latency for the DHCP DDNS updates in microseconds and the number of timeouts during different time intervals. The ibDHCPDDNSStats module contains the following objects:

ibDHCPStatistics

Object (Type)	Description
ibDHCPDDNSAvgLatency5 (Integer)	Indicates the average latency in microseconds of the DHCP DDNS updates in the last five minutes.
ibDHCPDDNSAvgLatency15 (Integer)	Indicates the average latency in microseconds of the DHCP DDNS updates in the last 15 minutes.
ibDHCPDDNSAvgLatency60 (Integer)	Indicates the average latency in microseconds of the DHCP DDNS updates in the last 60 minutes.
ibDHCPDDNSAvgLatency1440 (Integer)	Indicates the average latency in microseconds of the DHCP DDNS updates in the last 24 hours.
ibDHCPDDNSTimeoutCount5 (Integer)	The number of timeouts for the DHCP DDNS updates in the last five minutes.
ibDHCPDDNSTimeoutCount15 (Integer)	The number of timeouts for the DHCP DDNS updates in the last 15 minutes.
ibDHCPDDNSTimeoutCount60 (Integer)	The number of timeouts for the DHCP DDNS updates in the last 60 minutes.
ibDHCPDDNSTimeoutCount1440 (Integer)	The number of timeouts for the DHCP DDNS updates in the last 24 hours.

ibDHCPv6Module

The figure below illustrates the structure of the ibDHCPv6Module, which contains the following objects:

ibDHCPv6SubnetTable provides statistical data about the DHCPv6 operations of the appliance.
ibDHCPv6Statistics maintains counters for different types of packets.
ibDHCPv6DeferredQueuesize tracks the total number of deferred DDNS updates that are currently in the queue to be retried. When DDNS updates are deferred due to timeout or server issues, the DHCP server puts these updates in this queue.
ibDHCPv6DDNSStats monitors the average latency for the DDNS updates in microseconds and the number of timeouts during different time intervals.

ibDHCPv6Module

ibDHCPv6SubnetTable

ibDHCPSubnetTable provides statistical data about the DHCPv6 operations of the appliance. It contains the following objects:

ibDHCPSubnetTable

Object (Type)	Description
ibDHCPv6Subnet Entry	File that contains the objects for monitoring DHCPv6 operations on the appliance.
ibDHCPv6SubnetNetworkAddress (IbIpAddr)	The subnetworks, in IPv6 address format, that have IPv6 addresses for lease. A subnetwork may have many address ranges for lease.
ibDHCPv6SubnetNetworkMask (IbIpAddr)	The subnet mask in CIDR notation format.

ibDHCPv6Statistics

ibDHCPv6Statistics maintains counters for different types of packets. The counters always start with zero when the DHCP service is restarted. Therefore, the numbers reflect the total number of packets received since the DHCP service was last restarted on the appliance. The ibDHCPv6Statistics module contains the following objects:

ibDHCPv6Statistics

Object (Type)	Description
ibDhcpv6TotalNoOfSolicits (Counter)	The number of Solicit messages that the Grid member received, including Solicit messages embedded in Relay-Forward messages. A DHCP client sends a Solicit message to locate DHCP servers.
ibDhcpv6TotalNoOfRequests (Counter)	The number of Request messages that the Grid member received. A DHCP client sends a Request message to request one or more IP addresses and configuration parameters from a DHCP server.
ibDhcpv6TotalNoOfReleases (Counter)	The number of Release messages that the Grid member received. A DHCP client sends a Release message when it terminates its lease and releases its IP address.
ibDhcpv6TotalNoOfAdvertises (Counter)	The number of Advertise messages that the Grid member sent. When a DHCP server receives a Solicit message, it can respond with an Advertise message to indicate that the server is available for DHCP service.
ibDhcpv6TotalNoOfReplies (Counter)	The number of Reply messages that the Grid member sent. A DHCP server sends a Reply message that includes IP addresses and configuration parameters when it responds to Solicit, Request, Renew or Rebind message. It sends a Reply message with configuration parameters only when it responds to an Information-Request message.
ibDhcpv6TotalNoOfRenews (Counter)	The number of Renew messages that the Grid member received. A DHCP client sends a Renew message to a DHCP server to extend the lifetimes on the leases granted by the DHCP server and to update other properties.
ibDhcpv6TotalNoOfRebinds (Counter)	The number of Rebind messages that the Grid member received. A DHCP client sends a Rebind message to extend the lifetime of its lease and to update configuration parameters.
ibDhcpv6TotalNoOfDeclines (Counter)	The number of Decline messages that the Grid member received. A DHCP client sends a Decline message to a DHCP server when it discovers that the IP address offered by a DHCP server is already in use.
ibDhcpv6TotalNoOfInformationRequests (Counter)	The number of Information-Request messages that the Grid member received. A client sends an Information-Request message to retrieve configuration parameters, such as the IP addresses of DNS servers inthe network.
ibDhcpv6TotalNoOfOthers (Counter)	The total number of DHCP messages other than those used in negotiation.

ibDHCPv6DDNSStats

ibDHCPv6DDNSStats monitors the average latency for the DHCPv6 DDNS updates in microseconds and the number of timeouts during different time intervals. The ibDHCPv6DDNSStats module contains the following objects:
ibDHCPStatistics

Object (Type)	Description
ibDHCPv6DDNSAvgLatency5 (Integer)	Indicates the average latency in microseconds of the DHCPv6 DDNS updates in the last five minutes.
ibDHCPv6DDNSAvgLatency15 (Integer)	Indicates the average latency in microseconds of the DHCPv6 DDNS updates in the last 15 minutes.
ibDHCPv6DDNSAvgLatency60 (Integer)	Indicates the average latency in microseconds of the DHCPv6 DDNS updates in the last 60 minutes.
ibDHCPv6DDNSAvgLatency1440 (Integer)	Indicates the average latency in microseconds of the DHCPv6 DDNS updates in the last 24 hours.
ibDHCPv6DDNSTimeoutCount5 (Integer)	The number of timeouts for the DHCPv6 DDNS updates in the last five minutes.
ibDHCPv6DDNSTimeoutCount15 (Integer)	The number of timeouts for the DHCPv6 DDNS updates in the last 15 minutes.
ibDHCPv6DDNSTimeoutCount60 (Integer)	The number of timeouts for the DHCPv6 DDNS updates in the last 60 minutes.
ibDHCPv6DDNSTimeoutCount1440 (Integer)	The number of timeouts for the DHCPv6 DDNS updates in the last 24 hours.

ibDNSOne MIB

The ibDNSOne MIB provides DNS statistics about all zones in all views. The figure below illustrates the structure of the ibDNSOne MIB. (Note that the OIDs shown in the illustration do not include the prefix 1.3.6.1.4.1.7779.) The ibDNSOne MIB contains four subtrees: ibZoneStatisticsTable (Counter64), ibZonePlusViewStatisticsTable (Counter64), ibDDNSUpdateStatistics (Counter64), and ibBindZoneTransferCount (Counter64).

ibDNSOne MIB

Using the DNS Zone Statistics Tables

ibZoneStatistcisTable and ibZonePlusViewStatisticsTable provide DNS statistics for all zones in all DNS views, including the default and all user-defined DNS views. You can use the information in these tables to calculate the total number of recursive queries on the DNS server. Depending on whether your DNS server is an authoritative or a caching-only server, you calculate the total number of recursive queries differently.

ibZoneStatisticsTable

ibZoneStatisticsTable contains DNS statistics of all zones in the default DNS view. DNS statistics of user-defined DNS views are captured in ibZonePlusViewStatisticsTable.
ibZoneStatisticsTable includes a "summary" zone that provides global statistics for the DNS server, including statistics for all zones in the default and user-defined DNS views.
The syntax of the objects in ibZoneStatisticsTable uses a Counter64 format. In some cases, the counter format may not be compatible with SNMP toolkits that use a 32-bit counter. Ensure that you reconfigure or update these tools to use the Counter64 format. ibZoneStatisticsTable contains the following objects:

ibZoneStatisticsTable

Object (Type)	Description
ibBindZoneName (IbString)	DNS zone name. The index name for global statistics is “summary.”
ibBindZoneSuccess (Counter64)	The number of successful responses since the DNS process started.
ibBindZoneReferral (Counter64)	The number of DNS referrals since the DNS process started.
ibBindZoneNxRRset (Counter64)	The number of DNS queries received for non-existent records.
ibBindZoneNxDomain (Counter64)	The number of DNS queries received for non-existent domains.
ibBindZoneRecursion (Counter64)	The number recursive queries received since the DNS process started.
ibBindZoneFailure (Counter64)	The number of failed queries since the DNS process started.

Following is an example of the table as viewed through a MIB browser:

MIBBrowserView

ibZonePlusViewStatisticsTable

ibZonePlusViewStatisticsTable provides DNS statistics about all zones in user-defined DNS views. DNS statistics about zones in the default view are captured in ibZoneStatisticsTable. Note that information in ibZonePlusViewStatisticsTable is rolled up to the "summary" zone in ibZoneStatisticsTable.
The syntax of the objects in ibZonePlusViewStatisticsTable uses a Counter64 format. In some cases, the counter format may not be compatible with SNMP toolkits that use a 32-bit counter. Ensure that you reconfigure or update these tools to use the Counter64 format. ibZonePlusViewStatisticsTable contains the following objects:

ibZonePlusViewStatistics Table

Object (Type)	Description
ibBindZonePlusViewName (IbString)	The zone name.
ibBindZonePlusViewSuccess (Counter64)	The number of successful responses since the DNS process started.
ibBindZonePlusViewReferral (Counter64)	The number of DNS referrals since the DNS process started.
ibBindZonePlusViewNxRRset (Counter64)	The number of DNS queries received for non-existent records.
ibBindZonePlusViewNxDomain (Counter64)	The number of DNS queries received for non-existent domains.
ibBindZonePlusViewRecursion (Counter64)	The number of queries that caused recursion since the DNS process started.
ibBindZonePlusViewFailure (Counter64)	The number of failed queries since the DNS process started.
ibBindViewName (IbString)	The DNS view name.

Calculating Recursive DNS Queries

You can use the information in ibZoneStatisticsTable and ibZonePlusViewStatisticsTable to calculate the total number of recursive queries.
Following is an example of ibZoneStatisticsTable indexed by zone names in the default view:

index ibBindZoneNameibBindZoneSuccessibBindZoneReferralibBindZoneNxRRset

ibBindZoneNxDomainibBindZoneRecursionibBindZoneFailure

=====================================================================================================
"abc.com"abc.com000
0 0 0
"summary"summary500
0 0 0
"internal.com"internal.com100

0 0 0

Following is an example of ibZonePlusViewStatisticsTable indexed by zone names in all user-defined views:

index ibBindZonePlusViewNameibBindZonePlusViewSuccessibBindZonePlusViewReferralibBindZonePlusViewNxRRset

ibBindZonePlusViewNxDomainibBindZonePlusViewRecursionibBindZonePlusViewFailureibBindViewName

=====================================================================================================
"ext1.com"ext1.com100
        0 00 DNS1
"ext2.com"ext2.com200
        0 00 DNS1
"ext3.com"ext3.com000
        0 00 DNS2
Use the ibBindZoneSuccess object in both tables to determine the total number of recursive queries. If your DNS server is a caching-only server, the total number of recursive queries is the number indicated in the ibBindZoneSuccess object of the "summary" zone. In this example, for a caching-only server, the total number of recursive queries is 5.
If your DNS server is an authoritative server, add all the numbers in ibBindZoneSuccess for all zones in both tables, excluding the "summary" zone. In this example, the total is 4. You then subtract this number from the number in ibBindZoneSuccess of the "summary" zone. In this case, the total number of recursive queries is 1 for an authoritative DNS server.

ibDDNSUpdateStatistics

ibDDNSUpdateStatistics provides statistical data about DDNS updates. The counters always start with zero when the DNS service is restarted. They report the total numbers since the DNS service was last restarted.
ibDDNSUpdateStatistics contains the following objects:

ibDDNSUpdateStatistics

Object (Type)	Description
ibDDNSUpdateSuccess (Counter64)	The number of successful dynamic DNS updates.
ibDDNSUpdateFailure (Counter64)	The number of all failed dynamic DNS updates, excluding those reported by the ibDDNSUpdateReject object.
ibDDNSUpdateReject (Counter64)	The number of dynamic DNS updates that failed because they were denied by the DNS server.
ibDDNSUpdatePrerequisiteReject (Counter64)	The number of dynamic DNS updates that failed because the prerequisites were not satisfied. This is also included in the total number of failures reported by the ibDDNSUpdateFailure object.

ibBindZoneTransferCount

ibBindZoneTransferCount (Counter64) provides the total number of successful zone transfers from an Infoblox primary or secondary DNS server to a DNS client, since the DNS service was last restarted. Note that this counter tracks the number of successful full zone transfers (AXFRs) and incremental zone transfers (IXFRs).

IB-DNSSERV-MIB

The IB-DNSSERV-MIB contains one object, ibDnsServConfig, which reports the DNS BIND version implemented by the NIOS software.

IB-DNSHITRATIO-MIB

The IB-DNSHITRATIO-MIB contains one object, ibDnsHitRatio, which provides information about the DNS cache hit ratio. Note that the MIB variable (ibDNSOne) for cache hit rate has an OID of 1.3.6.1.4.1.7779.3.1.1.3.1.5.0, where 1.3.6.1.4.1.7779 is the prefix.

IB-DNSQUERYRATE-MIB

The IB-DNSQUERYRATE-MIB contains one object, ibDnsQueryRate, which provides information about the DNS queries per second. Note that the MIB variable (ibDNSOne) for DNS query rate has an OID of 1.3.6.1.4.1.7779.3.1.1.3.1.6.0, where 1.3.6.1.4.1.7779 is the prefix.

IB-DHCPSERV-MIB

The IB-DHCPSERV-MIB contains one object, ibDhcpv4ServerSystemDescr, which provides the DHCP server name and its DHCP version.

SNMP MIB Hierarchy

MIB Objects

System Object IDs

Infoblox MIBs

Loading the Infoblox MIBs

NET-SNMP MIBs

Note

BGP4 MIB

ibTrap MIB

Note

Interpreting Infoblox SNMP Traps

Types of Traps (OID 3.1.1.1.1)

Note

Trap Severity (OID 3.1.1.1.2.2.0)

ibProbableCause Values (OID 3.1.1.1.2.4.0)

ibSubsystemName Values (OID 3.1.1.1.2.5.0)

ibPreviousState (OID 3.1.1.1.2.9.0) and ibCurrentState (OID 3.1.1.1.2.10.0)

ibTrapDesc (OID 3.1.1.1.2.11.0)

Processing and Software Failure Traps

Threshold Crossing Traps

ibPlatformOne MIB

ibClusterReplicationStatusTable

ibNetwork Monitor

ibSystemMonitor

ibMemberServiceStatusTable

Infoblox Services for ibMemberServiceStatusTable

Service Status

ibMemberNodeServiceStatusTable

Infoblox Services for ibMemberNodeServiceStatusTable

ibMemberPassiveNodeServiceStatusTable

ibDHCPOne MIB

ibDHCPModule

ibDHCPStatistics

ibDHCPDDNSStats

ibDHCPv6Module

ibDHCPv6SubnetTable

ibDHCPv6Statistics

ibDHCPv6DDNSStats

ibDNSOne MIB

Using the DNS Zone Statistics Tables

ibZoneStatisticsTable

ibZonePlusViewStatisticsTable

Calculating Recursive DNS Queries

ibDDNSUpdateStatistics

ibBindZoneTransferCount

IB-DNSSERV-MIB

IB-DNSHITRATIO-MIB

IB-DNSQUERYRATE-MIB

IB-DHCPSERV-MIB